Abstract:Chemical components of perovskite layers play a key role in improving the efficiency and stability of perovskite solar cells. Pure inorganic perovskites exhibit good thermal and light stabilities; however, the smaller radius of Cs+ leads to a poor perovskite phase stability. In this case, the Cs-rich (CH(NH2)(2))(x)Cs1-xPbI3 ((CH(NH2)(2)(+)=FA(+)) perovskite seems more promising because it simultaneously offers the above- mentioned properties, while not forming an unstable perovskite phase. Thus far, the synthesis of Cs-rich FA(x)Cs(1)(-)(x)PbI(3) perovskite has been realized by introducing excess formamidinium iodide (FAI) as an additive. However, FAI sublimates at a high temperature and excessive FAI sublimation necessitates even greater temperatures. Therefore, it is difficult to precisely control the ratio of the sublimated FAI from the perovskite film. Herein, the precise synthesis of Cs-rich FA(x)Cs(1)(-)(x)PbI(3) perovskites at relatively low sublimation temperatures using amine additives, such as methylammonium iodide (MAI), dimethylamine iodide (DMAI), ethylamine iodide (EAI), ammonium iodide (NH41), and formamidine acetate (FAAC), was studied. The reaction temperature was reduced when utilizing these additives. Moreover, the window period for the preparation has been widened, which is particularly important for the preparation of pure phase Cs-rich FA(x)Cs(1)(-)(x)PbI(3) perovskite films for large devices. In the experiment, perovskite FA(0.15)Cs(0.)(85)PbI(3) was selected because of its good stability. The reaction process of the additive that assisted perovskite preparation was studied. Firstly, 0.85 mmol of MAI, DMAI, EAI, FAAC, and NH4I each were added to 1 mmol of FA(0.15)Cs(0.)(85)PbI(3) solution. Then, the precursor solution was spin-coated and thermally annealed. The FA(0.15)Cs(0.)(85)PbI(3) films were formed by sublimation of the additives during thermal annealing. The influence of different additives on the film formation process was traced using X-ray diffraction (XRD) measurements and UV-visible absorbance spectra (UV-Vis abs). The results showed that MAI and DMAI could be used as additives in the preparation of FA(0.15)Cs(0.)(85)PbI(3) films. The strong intermolecular interaction between these additives and PbI2 could benefit the formation of Cs4PbI6 and prevent the formation of delta-CsPbI3. Cs+ is easier to migrate in Cs4PbI6 than in delta-CsPbI3, which provides a necessary condition for the ion exchange reaction. Simultaneously, the mild sublimation temperature of the additives ensured that the films maintain their perovskite phase. Finally, pure phase Cs-rich FA(x)Cs(1-x)PbI(3) perovskites were prepared using this method at a relatively lower temperature of 200 degrees C. The XRD and UV-Vis absorption results confirmed the precise synthesis of FA(0.15)Cs(0.)(85)PbI(3). The FA(0.15)Cs(0.)(85)PbI(3) solar cells synthesized with MAI and DMAI achieved the maximum power conversion efficiencies of 15.6% and 15.1%, respectively.

CsI Pre-Intercalation in the Inorganic Framework for Efficient and Stable FA 1- x Cs x PbI 3 (Cl) Perovskite Solar Cells.

Cs0.15FA0.85PbI3/CsxFA1 -Xpbi3 Core/Shell Heterostructure for Highly Stable and Efficient Perovskite Solar Cells

Fabrication and Characterization of FA x Cs 1− x PbI 3 Polycrystal Perovskite Solar Cells

Aqueous Synthesis of Α-Csx FA1-x PbI3 Microcrystals for Efficient Perovskite Solar Cells

Fabrication and Characterization of FAxCs1−xPbI3 Polycrystal Perovskite Solar Cells

High-efficiency and thermally stable FACsPbI3 perovskite photovoltaics

Efficient Perovskite Solar Cells Fabricated Through CsCl-Enhanced PbI2 Precursor Via Sequential Deposition.

Over 24% efficient MA-free CsxFA1−xPbX3 perovskite solar cells

Cs4PbI6-Cl Nucleation Seeds Assisted Highly-Oriented Inorganic CsPbI3 Perovskites for Efficient Perovskite Solar Cells

Manipulating the Crystallization and Phase Transition for High-Performance CsPbI<sub>2</sub>Br Solar Cells

Constructing CsPbBr3 Cluster Passivated‐Triple Cation Perovskite for Highly Efficient and Operationally Stable Solar Cells

Fabricating Solid‐Solution‐Type Perovskite/Fluoride Nanocomposites Through Sublattice Interlocking for High‐Performance Photovoltaics

Optimizing the Light-Humidity Stability of Formamidinium Halide Perovskites Through Intermediate Phase and Strain Stress Adjustment

In Situ Constructing Intermediate Energy‐Level Perovskite Transition Layer for 15.03% Efficiency HTL‐Free Carbon‐Based Perovskite Solar Cells with a High Fill Factor of 0.81

Homogenizing Out-of-plane Cation Composition in Perovskite Solar Cells.

CsF Improved Buried Interface for Efficient and Stable Inverted All-inorganic CsPbI2.85Br0.15 Perovskite Solar Cells

Synthesis Of Cs-Rich Ch(Nh2)(2))(X)Cs1-Xpbi3 Perovskite Films Using Additives With Low Sublimation Temperature

Indium-Doped CsPbI2.5Br0.5 with a Tunable Band Structure and Improved Crystallinity for Thermo-Stable All-Inorganic Perovskite Solar Cells

Interface modification effect on the performance of Cs<sub>x</sub>FA<sub>1-x</sub>PbI<sub>y</sub>Br<sub>3-y</sub> perovskite solar cells fabricated by evaporation/spray-coating method

Stiffening the Pb-X Framework through a π-Conjugated Small-Molecule Cross-Linker for High-Performance Inorganic CsPbI 2 Br Perovskite Solar Cells

Lithium Fluoride Assisted Preparation of High‐performance All‐Inorganic CsPbI3 Perovskite Solar Cells