Abstract:The effect of nickel, tin, and indium additions in the eutectic Ag–28 wt.% Cu filler on the capillary and contact processes in brazing of VK94-1 and VK100 alumina ceramics and leucosapphire with VT1-0 titanium was examined. A special technique to study such processes was developed. This technique allows identifying, to the extent possible, the effect of different process parameters (heating rate, holding time, degree of vacuum, etc.) on the contact angles formed by metallic melts with different compositions on nonmetals in one experiment. High-temperature capillary and optical and scanning microscopy methods established that even small additions of nickel, tin, or indium to the eutectic Ag–Cu melt noticeably influenced the titanium dissolution rate and incipient wetting temperature of the nonmetallic substrate. Nickel additions were shown to enhance melt separation in the Ag–Cu–Ti system; in particular, the amount of the copper-based phase, eutectically melting with titanium above 870°C, increased. The effect of these additions in the Ag–28 wt.% Cu filler on the strength of brazed ceramic–ceramic joints produced using titanium foil inserts was studied. The results were discussed involving thermodynamic characteristics of the contacting structures. The role played by the type of chemical bonds in products resulting from interaction of the melt components and the solid substrate on the contact angle was shown. Brazed joints of alumina ceramics were made and used to determine the three-point-bending strength. The effect of various additions to the Ag–28 wt.% Cu filler on brazing strength was examined. Indium was found to be the most promising addition to the silver–copper filler as it allowed the brazing temperature to be controlled without a significant change in the mechanical strength of brazed joints.

Influence of the Brazing Paste Composition on the Wetting Behavior of Reactive Air Brazed Metal–Ceramic Joints

In situ observation of the pore formation during laser-based reactive air brazing of alumina

Evolution of microstructure and properties in reactive air brazing of 3YSZ ceramic and aluminized Crofer22h stainless steel using Pd-modified Ag–CuO filler

Reactive Air Brazing of Al2O3 Ceramic with Ag-CuO-Pt Composite Fillers: Microstructure and Joint Properties

Evolution Behavior of Al 2 O 3 Nanoparticles Reinforcements During Reactive Air Brazing and Its Role in Improving the Joint Strength

The influence of brazing conditions on joint strength in Al2O3/Al2O3 bonding

Zirconia and Crofer Joint Made by Reactive Air Brazing Using the Silver Base Paste and Cu-Ti Coating Layer

Reactive air brazing of YSZ ceramic with novel Al2O3 nanoparticles reinforced Ag-CuO-Al2O3 composite filler: Microstructure and joint properties

Study on Reactive Air Brazing of P-Sio2 Ceramic with Ag-xCuO Filler Metal

Microstructure and mechanical properties of brazing joint of silver-based composite filler metal

Microstructure and Performance of the Cu/Al2O3 Joint Brazed with Active Composite Filler

Brazing Between High Purity Alumina Ceramic and Oxygen-Free Copper

Recent Advances in Active Metal Brazing of Ceramics and Process

Process and Properties of Brazing High Volume SiCp/6063Al Composites with Glass

Bonding Mechanisms and Shear Properties of Alumina Ceramic/Stainless Steel Brazed Joint

Interfacial Microstructure and Mechanical Property of Brazed Copper/sio2 Ceramic Joint

Effect of Nickel, Tin, and Indium Doping of the Eutectic Silver–Copper Filler on the Capillary and Contact Processes in Brazing of Nonmetallic Alumina-Based Materials with Titanium

Interfacial Microstructure and Mechanical Properties of Pressureless Sintered SiC Ceramic and Stainless Steel Joints Brazed by AgCu/AgCuTi Alloy

Wettability and microstructural evolution of copper filler in W and EUROFER brazed joints

Research and Preparation of Silver Free Amorphous Active Brazing Alloy

Interfacial Microstructure and Mechanical Properties of SiC Joints Achieved by Reactive Air Brazing Using Ag-V2O5 Filler