Abstract:Laser modification techniques have been widely adopted in the field of surface engineering. Among these modified techniques, ultra-high-speed laser cladding is trending most nowadays to fabricate wear-resistant surfaces. The main purpose of this research is to provide a detailed insight of ultra-high-speed laser cladding of hard Ni60 alloy on LA43M magnesium alloy to enhance its surface mechanical properties. Multiple processing parameters were investigated to obtain the optimal result. The synthesized coating was studied microstructurally by field emission scanning electron microscopy (FESEM) equipped with an energy dispersive spectrometer (EDS) and X-ray diffraction (XRD). The microhardness and wear resistance of the Ni60 coating were analyzed under Vickers hardness and pin on disc tribometer respectively. The obtained results show that the dense Ni60 coating was fabricated with a thickness of 300 μm. No cracks and porosities were detected in cross-sectional morphology. The Ni60 coating was mainly composed of γ-Ni and hard phases (chromium carbides and borides). The average microhardness of coating was recorded as 948 HV0.3, which is approximately eight times higher than that of the substrate. Meanwhile, the Ni60 coating exhibited better wear resistance than the substrate, which was validated upon the wear loss and wear mechanism. The wear loss recorded for the substrate was 6.5 times higher than that of the coating. The main wear mechanism in the Ni60 coating was adhesive while the substrate showed abrasive characteristics.

Microstructure and properties of laser cladding Al-Si+Y2O3 coating on magnesium alloy

Influence of Laser Power on Microstructure and Properties of Al-Si+Y2O3 Coating

Effect of Y2O3 Addition on Microstructure and Properties of Laser Cladded Al-Si Coatings on AZ91D Magnesium Alloy

Laser Cladding of a Mg Based Mg–Gd–Y–Zr Alloy with Al–Si Powders

Microstructures and Properties in Surface Layers of Mg-6Zn-1Ca Magnesium Alloy Laser-Clad with Al-Si Powders

Laser Cladding of a Mg-Nd-Zn-Zr Alloy with Al-Si/Al(2)O(3 )Powders

Laser cladding Al-based amorphous-nanocrystalline composite coatings on AZ80 magnesium alloy under water cooling condition

Al2O3 eliminating defects in the Al coating by laser cladding to improve corrosion and wear resistance of Mg alloy

Microstructure and properties of in situ synthesized Fe-Al coating by laser cladding

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

Microstructure and Oxidation Resistance of the Laser-Clad Co22Cr12Al0.7Y Alloys

Enhanced Tribological Properties of LA43M Magnesium Alloy by Ni60 Coating Via Ultra-High-Speed Laser Cladding

Wear and Corrosion Resistance of Al0.5CoCrCuFeNi High-Entropy Alloy Coating Deposited on AZ91D Magnesium Alloy by Laser Cladding

Preparation and properties of nano ZrO2 coating on magnesium alloy

Microstructure, microhardness and corrosion resistance of laser cladding Ni–WC coating on AlSi5Cu1Mg alloy

Synthesis of Ni-WC/Al-Ni functionally graded coating with advanced corrosion and wear resistance on AZ91D Mg alloy by laser cladding

Microstructure and Properties of Mo-Si-B-Y2O3 Composite Coating on Nickel-Based Alloy by Laser Cladding

Microstructure and corrosion resistance of laser cladding and friction stir processing hybrid modification Al-Si coatings on AZ31B

Microstructural Transformation and High-Temperature Aluminum Corrosion Properties of Co-Based Alloy Coating Prepared by Laser Cladding

Effect of Si on Wear and Corrosion Resistance of Al0.5MnFeNiCu0.5Six/Al-Ni Gradient Coating by Laser Cladding

Microstructure and properties of Mo-Si-B-Y 2 O 3 composite coating on nickel-based alloy by laser cladding