Abstract:To synergistically improve the strength-ductility of copper alloys used in the miniaturized component, Cu-3.2Ti-0.2Fe-0.2V alloy with heterogeneous structure was obtained by thermo-mechanical treatment (namely, short-time annealing). The heterogeneous structure was composed of the non-uniform grains formed due to Laves phase inhibiting grain growth and FCC structured Cu4Ti phase with good coherent interface precipitated on the grain boundaries in sub-micro size. After aging at 400 °C for 2 h and then 450 °C for 4 h, the ultimate tensile strength and elongation of the heterogeneous-structured alloy were 976.8 MPa and 18.8% respectively, which was approximately 120 MPa more than that of the coarse-grained alloy after complete annealing, but both alloys had comparable ductility. When cold-rolling with 5% reduction was carried out before the aging of 450 °C, the strength increased to 1057 MPa and corresponding elongation was still over 10%. The strengthening mechanism of alloy with heterogeneous structure was analyzed and the hetero-deformation induced hardening of 284.5 MPa was the other significant reinforcement. The semi in-situ observation of tensile deformation behavior shown that the superior ductility in coarse-grained alloy was mainly attributed to the slipping and twinning. While grain rotation and grain boundary sliding were additional deformation mechanism in heterogeneous-structured alloy during tensile deformation, meanwhile, the texture of S, {110}<1 1 ‾ 1> and {331}<1 2 ‾ 3> components converted to the texture of {441}< 1 ‾ 1 ‾ 8>, Goss, Copper and {012}< 8 2 ‾ 1 > components. The deteriorative ductility after rolling with the reduction of 5% was owing to the S and Cube components converted to the strong texture of {032}<22 3 ‾ > components.

Optimizing the Electrical and Mechanical Properties of Cu-Cr Alloys by Hf Microalloying

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Increasing strength and electrical conductivity of Cu-0.77%Cr-0.86%Hf alloy by rotary swaging and subsequent aging

Precipitation behavior and microstructural evolution during thermo-mechanical processing of precipitation hardened Cu-Hf based alloys

Fabrication of High Strength Conductivity Submicron Crystalline Cu-5%Cr Alloy by Mechanical Alloying

Microstructure and mechanical properties of a Cu-1.28Cr-0.24P alloy with high electrical conductivity and tensile strength

Effect of micro-alloying element Ti on mechanical properties of Cu–Cr alloy

Microstructure and Property Evolution of Cu–9Ni–6Sn-xCr Alloys During Thermo-Mechanical Treatment Process

Effect of deformation and aging treatment on the microstructure and properties of Cu-0.45Cr-0.14Ti (wt.%) alloy

Influences of Cold Rolling and Aging on Microstructure and Property of CuCrSn Alloy

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment

Enhanced precipitation-hardening of Cu-Ag alloys through controlled chromium addition

Synergistic strengthening effects of precipitation and work hardening in cold-rolled Cu-0.4 wt%Cr alloy

Effect of two-step cryorolling and aging on mechanical and electrical properties of a Cu–Cr–Ni–Si alloy for lead frames applications

Effects of Hf additions on high-temperature mechanical properties of a directionally solidified NiAl/Cr(Mo) eutectic alloy

Effect of cryogenic rolling and multistage thermo-mechanical treatment on the microstructure and properties of the Cu-0.4Cr-0.39Zn-0.1Mg-0.07Zr alloy

Effect of Thermomechanical Processing on the Microstructure and Properties of a Cu-Fe-P Alloy

A novel precipitation‐strengthened conductive copper alloy: Cu‐Hf‐Si alloy

Alloying Effects on the Microstructure and Properties of CoCrFeMnNiX0.1 High-Entropy Alloys Via Rolling and Thermal Treatment