Abstract:The control of powder aging during Selective Laser Sintering (SLS) processing is one of the challenges to be overcome for the implementation of this technique in serial production. Aging phenomena, because of the elevated temperatures and long processing times, need to be considered when a fraction of the polymer powders present in the build chamber and not used to manufacture the parts are reused at various times. The aim of this study was to investigate the influence of successive reuse of blends of pure Polyamide 12 and its blends with two types of flame retardants (FR): ammonium polyphosphate (APP) and zinc borate (ZB). The composition of the blends was 70/30 (wt/wt) PA 12/FR. Four successive processing stages have been carried out by collecting the remaining powder blend each time. The powders were re-used using the same processing parameters after sieving. DSC measurements showed that the incorporation of FRs entailed a reduction in the processing window up to 4 °C; nevertheless, no further reduction was noted after aging. The TGA curves of aged blends of powders were also similar for pure PA 12 and PA 12 with FR. In addition, initial and reused powders presented a higher degree of crystallinity than the specimens processed from the powders. The heterogeneous character of the PA 12 after LS processing or reprocessing was shown through Pyrolysis Combustion Flow Calorimetry (PCFC) and cone calorimeter (CC) tests. FTIR analysis also showed that post-condensation reactions have occurred. The mode of action of the flame retardants was clearly seen on HRR curves at both tests. The first reuses of PA 12 powders entailed a significant reduction in time to ignition at the cone calorimeter (150 for the initial material to around 90 s for the reused material), indicating the formation of short polymer chains. Only in the case of zinc borate was it noticed that re-used powder was detrimental to the fire performance because of a strong increase in the value of pHRR (between 163 and 220 kW/m2 for reused material instead of 125 kW/m2 for the initial one).

Analysis of the feasibility of the reuse of polyamide 11 rejected in the manufacturing process of thermoplastic hoses of umbilicals

Recycling decommissioned polyamide 11: An approach to handle a previously unwanted material

Efficient Use of Secondary Raw Material from the Production of Polyamide Construction Products

Micromechanical Property Study of Nylon 11 and Organoclay Systems for Offshore Flexible Pipe

The degradation during recycling of polyamide 6 produced by anionic ring-opening polymerization of ε-caprolactam

Polyamide 6 and thermoplastic polyurethane recycled hybrid Fibres via twin-screw melt extrusion

Extrusion Parameters Optimization and Mechanical Properties of Bio-Polyamide 11-Based Biocomposites Reinforced with Short Basalt Fibers

Characterization of extruded films based on poly (butylene succinate) blends to utilize a partially degraded poly (butylene adipate‐co‐terephthalate)

The Effect of Reprocessing and Moisture on Polyamide Recycling: A Focus on Neat, Composites, and Blends

Abrasive wear of HDPE/UHMWPE blends

Towards the Reuse of Fire Retarded Polyamide 12 for Laser Sintering

Toward the production of bioblends for the automotive sector: Reuse of recycled polyamide 6,6 to prepare super‐tough biopolyethylene

Preparation and properties of nylon 11/ethylene‐vinyl alcohol/montmorillonite ternary composites

Melt Spinnability Comparison of Mechanically and Chemically Recycled Polyamide 6 for Plastic Waste Reuse

Rheological Insights into the Degradation Behavior of PP/HDPE Blends

Waste Management after the Injection Process by Manufacturing Polyamide Products Based on Regranulate

Recycling Polyethylene/Polyamide Multilayer Films with Poly(isoprene-g-Maleic Anhydride) Compatibilizer

The Recyclability of Fire-Retarded Biobased Polyamide 11 (PA11) Composites Reinforced with Basalt Fibers (BFs): The Influence of Reprocessing on Structure, Properties, and Fire Behavior

Development of Technologies for Processing Polypropylene Foil Waste and Their Use in the Production of Finished Products

Recycling and Reprocessing of Thermoplastic Polyurethane Materials towards Nonwoven Processing

Rheology, Morphology and Mechanical Properties for Mixtures of Multicomponent Waste from Polymer Composites as Secondary Raw Materials