Abstract:This paper describes the main results from an experimental investigation into tailoring the phase content and grain structure for high strength of a microstructurally flexible high entropy alloy (HEA), Fe42Mn28Co10Cr15Si5 (in at%), using rolling, friction stir processing (FSP), and compression. Optical microscopy, neutron diffraction, and electron backscatter diffraction were employed to characterize microstructure and texture evolution. The material upon rolling was found to have triplex structure consisting of metastable gamma austenite (γ), stable sigma (σ), and stable epsilon martensite (ε) phases. The adaptive phase stability exhibited by the selected HEA of very low stacking fault energy with strain, strain rate, and temperature was used along with grain refinement to enhance the strength. To this end, the complex structure was refined by FSP at 350 revolutions per minute (RPM) tool rotation rate, while increasing the fraction of γ and decreasing the σ and ε content. The strength was further enhanced by FSP at 150 RPM by further refinement of the grain structure and increasing the fraction of ε phase. The peak ultimate tensile strength of ~1850 MPa was achieved by double pass FSP (350 RPM followed by 150 RPM), the sequence which even more refined the microstructure and increased the fraction of σ phase. While the content of diffusion created σ phase remains constant during subsequent compression, the fraction of ε increases due to the diffusionless strain induced γ→ε phase transformation. The transformation facilitates plastic strain accommodation and rapid strain hardening, which has been attributed to the increase in highly dislocated ε phase fraction and transformation induced dynamic Hall-Petch-type barrier effect. Interestingly, a great deal of hardening ability was exhibited by the HEA even at very high strength. Roles of texture, grain size, and phase content on the transformation during compression have been rationalized and discussed in this paper.

Optimizing transformation-induced plasticity in CoCrNi alloys by combined grain refinement and chemical tuning

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Microstructure and deformation behavior of two TWIP/TRIP high entropy alloys upon grain refinement

Designing transformation-induced plasticity and twinning-induced plasticity Cr-Co-Ni medium entropy alloys: theory and experiment

Superb Strength-Ductility Synergy in a Medium-Entropy CoCrNi Alloy Via Reinforced TRIP Effect

Twin-induced transformation strengthening of CoCrNi-based medium-entropy alloy with a gradient nanostructure

Tuning Microstructure and Mechanical Performance of a Co-Rich Transformation-Induced Plasticity High Entropy Alloy

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Overcoming plasticity reduction in a severely deformed nano-grained metastable alloy

Hierarchical Grain Size and Nanotwin Gradient Microstructure for Improved Mechanical Properties of a Non-Equiatomic CoCrFeMnNi High-Entropy Alloy

TRIP-TWIP effect in deformation mechanisms of Co–Cr–Ni medium entropy via molecular dynamics simulations

Microstructure and Mechanical Properties of Microalloyed High-Strength Transformation-Induced Plasticity Steels

Composition design to tune the mechanical behavior of a TRIP-TWIP (CrMnFeCoNi)50 Fe50-xCrx multi-principal element alloys

Effect of Abnormal Grain Refinement on Synchronous Strengthening Behavior of Fe50Mn30Co10Cr10 High Entropy Alloys

Revealing the deformation mechanisms of symmetric tilt grain boundaries in CoCrNi medium-entropy alloy

α" martensite engineering: A strategy to achieve high yield strength and low yield ratio synergy for dual-phase titanium alloy

The Effects of Microstructure Refinement and Coincidence Site Lattice Boundaries on the Plasticity of FeCrAlY Alloys

Enhanced strength-ductility synergy in a Ta-doped CoCrNi medium-entropy alloy with a dual heterogeneous structure

Facile route to implement transformation strengthening in titanium alloys

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy

Synergistic grain boundary engineering for achieving strength-ductility balance in ultrafine-grained high-Cr-bearing multicomponent alloys