Abstract:This paper describes the main results from an experimental investigation into tailoring the phase content and grain structure for high strength of a microstructurally flexible high entropy alloy (HEA), Fe42Mn28Co10Cr15Si5 (in at%), using rolling, friction stir processing (FSP), and compression. Optical microscopy, neutron diffraction, and electron backscatter diffraction were employed to characterize microstructure and texture evolution. The material upon rolling was found to have triplex structure consisting of metastable gamma austenite (γ), stable sigma (σ), and stable epsilon martensite (ε) phases. The adaptive phase stability exhibited by the selected HEA of very low stacking fault energy with strain, strain rate, and temperature was used along with grain refinement to enhance the strength. To this end, the complex structure was refined by FSP at 350 revolutions per minute (RPM) tool rotation rate, while increasing the fraction of γ and decreasing the σ and ε content. The strength was further enhanced by FSP at 150 RPM by further refinement of the grain structure and increasing the fraction of ε phase. The peak ultimate tensile strength of ~1850 MPa was achieved by double pass FSP (350 RPM followed by 150 RPM), the sequence which even more refined the microstructure and increased the fraction of σ phase. While the content of diffusion created σ phase remains constant during subsequent compression, the fraction of ε increases due to the diffusionless strain induced γ→ε phase transformation. The transformation facilitates plastic strain accommodation and rapid strain hardening, which has been attributed to the increase in highly dislocated ε phase fraction and transformation induced dynamic Hall-Petch-type barrier effect. Interestingly, a great deal of hardening ability was exhibited by the HEA even at very high strength. Roles of texture, grain size, and phase content on the transformation during compression have been rationalized and discussed in this paper.

Microstructure and deformation behavior of two TWIP/TRIP high entropy alloys upon grain refinement

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Microstructural design and deformation behavior of a TRIP/TWIP tri-phase heterogeneous high-entropy alloy

Optimizing transformation-induced plasticity in CoCrNi alloys by combined grain refinement and chemical tuning

Transition of twinning behavior in CoCrFeMnNi high entropy alloy with grain refinement

Tuning Microstructure and Mechanical Performance of a Co-Rich Transformation-Induced Plasticity High Entropy Alloy

Delving into the intrinsic co-relation between microstructure and mechanical behaviour of fine−/ultrafine-grained TWIP steels via TEM and in-situ EBSD observation

Hierarchical Grain Size and Nanotwin Gradient Microstructure for Improved Mechanical Properties of a Non-Equiatomic CoCrFeMnNi High-Entropy Alloy

Achieving excellent strength-ductility synergy via high density dislocation and nano-twinning in cryo-rolled FeCoCrNiMo0.2 high-entropy alloy

Microstructure Refinement of a Transformation-Induced Plasticity High-Entropy Alloy

Plasticity Improvement in a Co-Rich Co<sub>40</sub>Fe<sub>25</sub>Cr<sub>20</sub>Ni<sub>15</sub> High-Entropy Alloy via Al Alloying

Trace B doping Fe50Mn30Co10Cr10 high entropy alloy: Mechanical response and multi-microstructure evolution under TWIP and TRIP effects

Plasticity Improvement in a Co-Rich Co40Fe25Cr20Ni15 High-Entropy Alloy via Al Alloying

TRIP-TWIP effect in deformation mechanisms of Co–Cr–Ni medium entropy via molecular dynamics simulations

Regulation of strength and ductility of single-phase twinning-induced plasticity high-entropy alloys

Deformation mechanism and microstructure evolution during superplastic deformation of friction stir processed CoCrFeNiMn high entropy alloy

The relative contributions of TWIP and TRIP to strength in fine grained medium-Mn steels

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Plastic deformation behavior of ultrafine grained CoCrFeNiMn high entropy alloy with nanoparticles

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy