Abstract:It is common on space vehicles to have thermal insulation adhesively bonded to a metal structure. A typical defect in such structures is an interlayer disbond, which may occur either between the insulation and the metal substructure or between the layers of multilayer thermal insulation. One-sided thermal nondestructive testing (TNDT) using surface optical heating, such as Xenon flash or quartz tube, may detect disbonds if the thermal insulation thickness does not exceed a few millimeters and disbonds are not very small. In thicker insulation, the effectiveness of the inspection can be improved by using electrical induction to heat the metal base. In both cases, thermal excitation can be areal heating, which is heat projected over an area by a stationary heat source, or scanned linear heating (SLH), which is a linear heater scanned across the test subject. In the latter, either the linear heater is moved across a stationary test subject, or the linear heater is stationary and the test subject is moved. The SLH method usually provides a higher inspection rate (inspected area unit time). In this research, both the theoretical and experimental features of both optical and induction heating have been investigated and compared in the application to non-metallic insulation adhesively bonded to a metal structure. The effectiveness of using neural networks (NN) for characterizing defects has also been studied to demonstrate that optimal NN training should involve 4–5 points selected in defect areas close to non-defect areas, and the NN input data should be prepared by applying the known technique of Thermographic Signal Reconstruction (TSR). Since SLH provides more uniform heating, it provides higher quality IR thermograms than those obtained from areal (flash) heating and this improves the detectability of defects in thermal insulation to a depth of 4–6 mm. Other advantages of SLH for TNDT testing are (1) an inspection rate that is twice as high as an area heating technique and (2) a better potential for fully automated (robotic) testing.

Analyzing efficiency of optical and THz infrared thermography in nondestructive testing of GFRPs by using the Tanimoto criterion

Thermal non‐destructive testing and evaluation for inspection of carbon fibre‐reinforced polymers

Efficiency of using different types of infrared imagers in active thermal nondestructive testing of delaminations in non-metals

Applications of Independent Component Thermography for Testing and Evaluation of Glass Fibre Reinforced Polymer Materials

Comparative Studies of GFRP Composites Using Pulsed Thermography and Transmission Terahertz Non-Destructive Testing Methods

Comparative Analysis of Single- and Multiple-Frequency Thermal Wave Radar Imaging Inspection of Glass Fiber Reinforced Polymer (GFRP)

Novel Insights on Spatio-Temporal Analysis for Frequency Modulated Thermal Wave Imaging Using Principal Component Analysis on Glass Fibre Reinforced Polymer Material

Defect Detection of GFRP Composites through Long Pulse Thermography Using an Uncooled Microbolometer Infrared Camera

Defect Detection Capabilities of Pulse Compression Based Infrared Non-Destructive Testing and Evaluation

Time-Frequency Based Thermal Imaging: An Effective Tool for Quantitative Analysis

INFRARED THERMOGRAPHY TECHNIQUE FOR DAMAGE DETECTION ON COMPOSITE MATERIALS UNDER LOW-ENERGY IMPACT

Nondestructive Evaluation of Composite Bonding Structure Used in Electrical Insulation Based on Active Infrared Thermography

Infrared Polarization Imaging-based Non-destructive Thermography Inspection

Nondestructive detection of CFRP subsurface defects using transient lock-in thermography

An Edge-Filtered Optical Fiber Interrogator for Thermoplastic Polymer Analysis

Experimental study on defects detection in GFRP laminates using lock-in infrared thermography technology

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

The Wrinkles Characterization in GFRP Composites by Infrared Active Thermography

Infrared Laser Heating of GFRP Bars and Finite Element Temperature Field Simulation

The Detection and Characterization of Defects in Metal/Non-metal Sandwich Structures by Thermal NDT, and a Comparison of Areal Heating and Scanned Linear Heating by Optical and Inductive Methods

Thermal Nondestructive Testing of Composite and Metal Parts Manufactured by Additive Technologies