Abstract:Owing to their superior mechanical properties of high hardness, wear resistance, and corrosion resistance, CoCrFeNiTi high entropy alloys (HEAs) attracted the attention of researchers to use as coating materials for titanium (Ti) and its alloys. Directed energy deposition (DED) has the potential to combine both the fabrication process and the laser remelting process (implemented by double laser scanning) using the same equipment set-up. With high energy density and rapid cooling rate, combining DED and laser remelting is considered an effective method to enhance solid solution strengthening effects and element segregation of CoCrFeNiTi HEA coatings, thus being able to affect HEA coatings' phase constitutions, microstructure, and mechanical properties. To date, there are no reported publications on the deposition of CoCrFeNiTi HEA coatings via the combination of DED and laser remelting process. In addition, the investigation of the effects of remelting laser power is still lacking. To fill these gaps, the relationships among the levels of remelting laser power, molten pool properties, microstructure, and mechanical properties of CoCrFeNiTi HEA coatings are built by DED with the laser remelting process in this investigation. When the remelting laser power is higher than 225 W (75 % of the laser power in the DED process), the three-phase microstructure changes to a two-phase microstructure. The higher molten pool temperature, lower cooling rate, and secondary solidification induced by a relatively high remelting laser power can enhance the solid solution strengthening effects and promote the precipitation of the high-hardness Χ phase and Laves phase. After the 300 W laser remelting process, the highest average microhardness of the coatings is obtained as 916 HV 1.0 , which is 65 % higher than that of the coatings without laser remelting process. The best wear resistance is observed in the coatings with 225 W remelting laser power instead of 300 W remelting laser power since the high content of brittle phase caused by high remelting laser power could promote the formation of abrasive particles during the dry sliding tests.

Strengthening behavior of AlCoCrFeNi(TiN) high-entropy alloy coatings fabricated by plasma spraying and laser remelting

Microstructure and wear resistance of in-situ TiC reinforced AlCoCrFeNi-based coatings by laser cladding

Microstructure and wear behavior of mechanically alloyed powder AlxMo0.5NbFeTiMn2 high entropy alloy coating formed by laser cladding

Mechanical and chemical properties of CoCrFeNiMo0.2 high entropy alloy coating fabricated on Ti6Al4V by laser cladding

AlxCoCrFeNiSi high entropy alloy coatings with high microhardness and improved wear resistance

Microstructure and Friction Properties of CoCrFeMnNiTix High-Entropy Alloy Coating by Laser Cladding

Microstructure and wear resistance of TiAlNiSiV high-entropy laser cladding coating on Ti-6Al-4V

Preparation of CrCoFeNiMn High-Entropy Alloy Coatings Using Gas Atomization and Laser Cladding: An Investigation of Microstructure, Mechanical Properties, and Wear Resistance

Microstructural characterization and corrosion behaviour of AlCoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Cultivating a Comprehensive Understanding of Microstructural Attributes and Wear Mechanisms in FeCrCoNiAlTi x High-Entropy Alloy Coatings on TC6 Substrates Through Laser Cladding Fabrication

High-temperature oxidation behavior and corrosion resistance of in-situ TiC and Mo reinforced AlCoCrFeNi-based high entropy alloy coatings by laser cladding

Investigation into corrosion and wear behaviors of laser-clad coatings on Ti6Al4V

FeNiCrCoCuxMo High Entropy Alloy (HEA) Coatings Fabricated by Laser Cladding

Investigation on the relationship between reinforcing behavior of TiN and wear resistance of AlCoCrCuNiTi high-entropy alloy coating

Effects of Ti content on the microstructure and properties of AlCoCrFeNiTix high-entropy alloys prepared by laser cladding

Microstructures and Wear Resistance of CoCrFeNi2V0.5Tix High-Entropy Alloy Coatings Prepared by Laser Cladding

Microstructure and wear behaviour of in-situ TiN-Al2O3 reinforced CoCrFeNiMn high-entropy alloys composite coatings fabricated by plasma cladding

Microstructure and tribological properties of in-situ M x B reinforced CoCrFeNi HEA composites prepared by laser cladding

Microstructure, thermostability and tribological behavior of composite CoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Microstructure and Wear Resistance of FeCuNiTiAl High-Entropy Alloy Coating on Ti6Al4V Substrate Fabricated by Laser Metal Deposition

Laser remelting of CoCrFeNiTi high entropy alloy coatings fabricated by directed energy deposition: Effects of remelting laser power