Abstract:High-strength low-alloy steels (HSLA) are gaining popularity in structural applications in which weight reduction is of interest, such as heavy duty machinery, bridges, and offshore structures. Since the fatigue behavior of welds appears to be almost independent of the base material and displays little improvement when more resistant steel grades are employed, the use of bolted joints is an alternative joining technique which can lead to an increased fatigue performance of HSLA connections. Manufacturing a hole to allocate the fastener elements is an unavoidable step in bolted elements and it might induce defects and tensile residual stresses that could affect its fatigue behavior. This paper studies and compares several mechanical (punching, drilling, and waterjet-cut) and thermal (plasma and laser-cut) hole-making procedures in HSLA structural plates. A series of 63 uniaxial fatigue tests was completed, covering three HSLA grades produced by thermomechanically controlled process (TMCP) with yield strength ranging from 500 to 960 MPa. Samples were tested at single load level, which was considered representative in HSLA typical applications, according to the input received from end users. The manufactured holes were examined by means of optical and electron microscopy, 3D point measurement, micro hardness tests, X-ray diffraction, and electron backscatter diffraction (EBSD). The results give insight on cutting processes in HSLA and indicate how the fatigue failure is dominated by macro defects rather than by the steel grade. It was shown that the higher yield strength of the HSLA grades did not lead to a higher fatigue life. Best fatigue results were achieved with laser-cut specimens while punched samples withstood the lowest amount of cycles.

Fatigue Crack Growth on Flash Butt Welded and Laser Beam Welded Joints in a High-Strength Low-Alloy Steel

Microstructure and fatigue properties of friction stir welded high-strength steel plates

Study on fatigue behavior of butt-welded high-strength steel connections with surface cracks

MICRO-CRACK ANALYSIS IN THE STUDY OF FATIGUE FRACTURE IN THE HAZ IN THE HIGH YIELD STRENGTH MICRO-ALLOYED STEELS

Fatigue Properties and Fracture Behavior of Al/steel Butt Joints Fabricated by Laser‐mig Welding‐brazing

A Comparative Study on Microstructural Characterization of Thick High Strength Low Alloy Steel Weld by Arc Welding and Laser Welding

Fatigue and impact properties of single and double resistance spot welding for high-strength steel used in automotive applications

Study on microstructure evolution and mechanical properties of high-strength low-alloy steel welds realized by flash butt welding thermomechanical simulation

Microstructure and mechanical properties of HSLA thick plates welded by novel double-sided gas metal arc welding

Understanding of Fatigue Crack Growth Behavior in Welded Joint of a New Generation Ni-Cr-Mo-V High Strength Steel

Interactions of the process parameters and mechanical properties of laser butt welds in thin high strength low alloy steel plates

High-cycle rotating-bending fatigue performance of S690QL welded joints

Failure Mechanisms of Mechanically and Thermally Produced Holes in High-Strength Low-Alloy Steel Plates Subjected to Fatigue Loading

Microstructural and interface geometrical influence on the mechanical fatigue property of aluminum/high-strength steel lap joints using resistance element welding for lightweight vehicles: experimental and computational investigation

Fatigue Crack Growth Rates in Friction Stir Welding Joints of Al-Li 2060-T8X Alloy

Mechanical property and microstructure of HSLA steel laser hybrid welded joint

Fiber Laser Welding of HSLA Steel by Autogenous Laser Welding and Autogenous Laser Welding with Cold Wire Methods

Influence of Heat Input on the Changes in the Microstructure and Fracture Behavior of Laser Welded 800mpa Grade High-Strength Low-Alloy Steel

A Fracture Mechanics-Based Optimal Fatigue Design Method Of Under-Matched Hsla Steel Butt-Welded Joints With Imperfections

Study on microstructure evolution in welded lap joint configuration of dissimilar advanced high-strength steels using low-frequency laser wobble welding

Study on Fatigue Behavior and Crack Propagation Life of Longitudinal Fillet Welded Lap Joint