Abstract:Different load spectra and individual load peaks might substantially relax high residual stresses as well as induce compressive residual stresses in welded components and, consequently, affect the fatigue performance of these joints. Consideration of peak loads and resulting relaxation of residual stresses in fatigue analyses can substantially enhance the accuracy of life prediction. The aim of the current study is to experimentally investigate the fatigue strength of welded joints subjected to different levels of overloads and variable amplitude (VA) loads and to develop local fatigue assessment method to account for the relaxation of residual stresses via a mean stress correction using the 4R method. The 4R method applies a local stress ratio for the mean stress correction considering material strength, residual stresses, applied stress ratio of external loading and local weld geometry in elastic–plastic material behaviour. Fatigue tests were carried out on fillet-welded longitudinal gusset joints made of S700 high-strength steels under applied stress ratio R = 0–0.1. A mild strength steel (S355) and ultra-high-strength steel (S1100) were selected as reference steel grades for the fatigue testing to study the material strength effects. Numerical analyses were conducted to evaluate the fatigue notch factors using the effective notch stress concept with the reference radius of r ref = 1.0 mm and theory of critical distance (TCD) using the point method. The experimental results indicated that a substantial improvement in the fatigue strength capacity can be claimed in the joints subjected to tensile overloads, particularly in the studied S700 and S1100 steels. The higher-level overload (0.8 f y ), corresponding to the nominal cross-sectional area, improved the mean fatigue strength of the welded joints manufactured of high-strength S700 steel by approximately 60%, while the lower overload (0.6 f y ) improved the mean fatigue strength by 20%. In addition, a use of equivalent nominal stresses for the joints subjected to VA loads resulted in conservative assessments when employing S–N curves obtained for the CA loading. The 4R method, via the local mean stress correction for individual cycles, provided higher accuracy for the fatigue assessments.

Influence of steel strength and loading mode on fatigue properties of resistance spot welded H beam components

Influence of steel strength and loading mode on fatigue properties of resistance spot welded H section specimen

Fatigue Testing in Welded Joint of 980- grade Steels

Fatigue and impact properties of single and double resistance spot welding for high-strength steel used in automotive applications

Effect of Loading Methods on the Fatigue Properties of Dissimilar Al/Steel Keyhole-Free FSSW Joints

Microstructural and interface geometrical influence on the mechanical fatigue property of aluminum/high-strength steel lap joints using resistance element welding for lightweight vehicles: experimental and computational investigation

Fatigue Crack Growth on Flash Butt Welded and Laser Beam Welded Joints in a High-Strength Low-Alloy Steel

Effects of Sheared Edge and Overlap Length on Reduction in Tensile Fatigue Limit before and after Hydrogen Embrittlement of Resistance Spot-Welded Ultra-High-Strength Steel Sheets

Effects of welding residual stresses on fatigue reliability assessment of a PC beam bridge with corrugated steel webs under dynamic vehicle loading

Overload and variable amplitude load effects on the fatigue strength of welded joints

Effect of Forging Force on Fatigue Behavior of Spot Welded Joints of Aluminum Alloy 5182

Welding residual stress behavior under mechanical loading

Microstructure and Fatigue Properties of Mg-To-Steel Dissimilar Resistance Spot Welds

A Fatigue Life Prediction Approach for Resistance Spot Welded Joints with Consideration of the Stress Ratio Effect

Microstructure and fatigue properties of friction stir welded high-strength steel plates

Low-cycle fatigue in ultra-high-strength steel welded joints in the as-welded and post-weld-treated conditions

Fatigue enhancement of welded thin-walled tubular joints made of lean duplex steel

The Influence of the Ratio of Circumference to Cross-Sectional Area of Tensile Bars on the Fatigue Life of Additive Manufactured AISI 316L Steel

Fatigue Behaviour of Steel Elements Strengthened with Stand CFRP Sheets

Fatigue strength estimation of butt-welded joints between cast-steel and hot-rolled-steel plates

An experimental methodology to characterize load-based fracture models of third generation advanced high strength steel resistance spot welds