Abstract:Purpose. Research of cutting force components during machining of high-hard cast iron by special prefabricated cutters with brazed niborite and ciborite inserts. Determination of the influence of geometric characteristics of the cutting tool, cutting modes and hardness of the material being machined on the cutting forces. The methods. The research methods were based on the fundamentals of cutting theory and cutting tools, material science properties of the tool and processed material. A research bench with special equipment was used. Findings. The nature of the change in the components of cutting forces with depth t, feed rate S and cutting speed v was experimentally investigated. The studies have shown an excess of the resulting force in the horizontal plane Pv over the circumferential one Pz, which is the main feature of turning high-hard metals. It has been established that the main limiting factors in the wear of tool cutting inserts are the permissible levels of forces. The hardness of HB has the greatest effect on the radial force Py. Under identical turning conditions for materials with a hardness of 220 to 610 HB, the forces Pz, Py and Px increase by 1,7; 3,3 and 2,3 times, respectively. In addition to the natural increase, the ratio of cutting forces also changes. Reducing the front angle of the blade causes a deterioration in chip formation conditions and leads to an increase in all components of the cutting forces. An increase in the radius at the top of the cutter r causes an increase in the width and decrease in the thickness of the layer to be cut, as well as a decrease in the main angle in the plan φr on the radial part of the blade. The originality. A complex dependence in the structural-stage form was obtained, which gives a clear picture of the influence of each parameter of the turning process on its performance. This dependence is a mathematical model for calculating the optimal operating and geometric parameters of the turning process of high-hard cast irons. The influence of the frontal angle γ, wear value h, and hardness of HB cast iron on the power characteristics during machining of high-hard cast irons has been studied. Practical implementation. It has been shown that it is economically advantageous to maximize the wear of cutting inserts made of relatively expensive composites. In this case, it is necessary to use a technological system of machine-workpiece-tool of high rigidity.

INCREASING THE WEAR RESISTANCE OF THE CUTTING TOOL

Application of Magnetron Sputter Ion Plated CrAlTiN Composite Coating in Improving Wear Resistance of Milling Cutter

Interactive methods for increasing wear resistance of cutting tool blades

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Study of cutting forces during turning of high-hard cast irons

Study of the influence of cutting parameters on tool wear and the state of the machined surface

Improving Maraging Steel 350 Machinability via Wiper Insert-Enhanced Face Milling

ASSESSMENT OF WEAR AND DESTRUCTION OF SOLID CARBIDE CUTTERS DURING MILLING OF HARDENED STEEL 4X5MF1C WITH A HARDNESS OF 52 HRC

Enhancement of carbide tool performance during dry machining through a combination of laser surface texturing and tungsten disulfide soft coatings

An anti-wear tool structure with integrated-micro hybrid cutting edges for milling of carbon fiber–reinforced plastics composites

The Influence of Surface Texturing of Ceramic and Superhard Cutting Tools on the Machining Process—A Review

Study on the Friction-Reducing Mechanisms of Surface Texture Cemented Carbide under Dry Sliding

Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel

Wear of End Mills with Carbon Coatings When Aluminum Alloy A97075 High-Speed Processing

Experimental investigation of micro-pillar textured WC inserts during turning of Ti6Al4V under various cutting fluid strategies

Experimental Study on the Effect of Cutting Tool Geometry in Micro-Milling of Inconel 718

Tribological Aspects of Cutting Tool Wear during the Turning of Stainless Steels

Tool degradation effect on roughness factor in the process of physical modeling of cylindrical gear shaving and rolling

Cutting performance and wear mechanisms of PVD coated carbide tools during dry drilling of newly produced ADI

Effect of Different Geometric Texture Shapes on Wettability and Machining Performance Evaluation Under Dry and MQL Environments

Wear Resistance and Titanium Adhesion of Cathodic Arc Deposited Multi-Component Coatings for Carbide End Mills at the Trochoidal Milling of Titanium Alloy