Abstract:High-speed steel (HSS) tools account for 20 percent of the cutting tools materials' global market. This is due to both their significant toughness and resistance to cracking, compared to cemented carbides. Covering steel tools with hard coatings clearly improves their mechanical properties, wear resistance, and significantly increases their durability. Physical vapor deposition methods are preferred for coating metal substrates, as they allow low temperature deposition. The most widely deposited coating materials are carbides, nitrides, and borides. They are combined with softer ones in the multilayer structure to promote increased resistance to cracking and delamination in comparison to monolayered structures. In this paper, the M2 steel end mills were coated by (TiBx/TiSiyCz) x3 multilayer by the pulsed laser deposition method. Coated and uncoated tools were tested in the cylindrical down milling of AISI 316L steel. Components of the cutting force and temperature generated in the machined area during dry milling were measured under two variants of operating conditions: V1 and V2. Tool wear mechanism was examined using scanning electron microscopy (SEM), accompanied by EDS analysis of worn areas. It was found that milling with higher speed (variant V2) is accompanied by lower cutting force components and a lower temperature generated in cutting area. The presence of the coating allowed lower cutting forces and temperature in the case of variant V1. The temperature measured during milling did not exceed 200 °C. The SEM observation of the edges of cutting tools indicated that the main mechanism of wear for both types of tools was abrasion. The built-up edge formation was observed in the case of tools tested at the V1 cutting parameters variant. It was assumed that it was the reason for higher cutting forces measured during milling according to this variant. The chemical composition of built-up edges was different for coated and uncoated tools. Tribo-chemical reactions were responsible for the reduction of the cutting force and temperature components observed during milling with a coated tool at V1 variant. Boron and titanium were the elements of the coating that enabled the tribo-oxidation reactions thanks to which friction was reduced. Our results show that this beneficial effect occurs with (TiBx/TiSiyCz) x3 coated tools, but can easily be lost with inadequately selected cutting parameters.

ASSESSMENT OF WEAR AND DESTRUCTION OF SOLID CARBIDE CUTTERS DURING MILLING OF HARDENED STEEL 4X5MF1C WITH A HARDNESS OF 52 HRC

Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling

Wear of End Mills with Carbon Coatings When Aluminum Alloy A97075 High-Speed Processing

Cutting edge wear in high-speed stainless steel end milling

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

The Surface Integrity in Machining Hardened Steel Skd11 for Die and Mold

Investigation of TiCrN-Coated High Speed Steel Tools Wear during Medium Density Fiberboard Milling

Experimental investigation on hard milling of high strength steel using PVD-AlTiN coated cemented carbide tool

EXPERIMENT ON SURFACE INTEGRITY OF MILLING TOOL FOR HARDENED STEEL SKD11

Study on Surface Integrity in Hard Milling of Hardened Die Steel

The Comparative Studies on the Surface Integrity in Milling and Grinding Hardened Steel SKD11

Analysis of Tool Wear in GH4169 Material Milling Process

Method of Tool Wear Control during Stainless Steel End Milling

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Comparative Study On The Surface Qualities In Grinding And Milling Hardened Steel Skd11

Measurement of roughness on hardened D-3 steel and wear of coated tool inserts

Investigation on Performance of a CVD Coated Carbide Tool in Face Milling of Ultra-High Strength Steel 30Cr3SiNiMoVA

Intercomparison of Indexable Cutting Inserts' Wear Progress and Chip Formation During Machining Hardened Steel AISI 4337 and Austenitic Stainless Steel AISI 316 L

Wear Behaviour of High Strength Tool Steel 90MnCrV8 in Contact with Si3N4

Impact of Deposition of the (TiBx/TiSiyCz) x3 Multilayer on M2 HSS on the Cutting Force Components and Temperature Generated in the Machined Area during the Milling of 316L Steel

Experiment Study on Cutter Disrepair Principle and Optimization for Machining Heat-Resistant Steel