Abstract:In this study, Spark Plasma Sintering (SPS) was utilized to fabricate fine-grained cemented carbides, and an orthogonal experimental design was employed to examine the influence of holding temperature (1100 °C, 1200 °C, 1300 °C) and holding time (5, 10, and 15 min) on the performance of WC-10Co cemented carbide specimens. Compared with conventional sintering methods, this work achieved the production of samples with enhanced overall performance at lower temperatures and shorter durations. Specifically, under the conditions of a holding temperature of 1300 °C and a holding time of 5 min, the resulting specimens exhibited a density of 14.64 g/cm3, a hardness of 91.29 HRA, a fracture toughness of 16.39 MPa·m½, and a transverse rupture strength of 2398 MPa. The microstructural analysis revealed that as the holding temperature increased, the Co phase in the specimens underwent a transformation from its initial powder form to banded cobalt and subsequently to slit-shaped cobalt. It was found that the presence of banded cobalt effectively hinders crack propagation, whereas slit-shaped cobalt is more effective in preventing crack initiation, thus impacting the overall performance of the specimens. By analyzing the sintering curves and microstructures, the densification mechanisms during SPS sintering of WC-Co cemented carbides were elucidated. The study concluded that the state changes of the Co phase play a significant role in the densification behavior, final microstructure, and properties of the sintered material. These findings offer valuable insights for understanding and optimizing the SPS process.

Binderless tungsten carbides with an increased oxygen content obtained by spark plasma sintering

An investigation of the peculiarities of high-speed sintering of plasma chemically synthesized tungsten carbide nanopowders with increased oxygen content

Combined effect of SiC and carbon on sintering kinetics, microstructure and mechanical properties of fine-grained binderless tungsten carbide

Spark Plasma Sintering Of Nanocrystalline Wc/Co Cemented Carbides

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Binderless nanocrystalline tungsten carbide with enhanced hardness induced by high-pressure sintering

Bulk Ultrafine Binderless WC Prepared by Spark Plasma Sintering

Spark Plasma Sintering of Ultrafine WC-5%Co Cemented Carbide Composite Powders

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

Spark Plasma Sintering of Fine-Grained WC-Co Composites

Phase Composition and Microstructure of Binderless Wc-Zrc Cemented Carbides Fabricated by Spark Plasma Sintering

Microstructures and Properties of Ultrafine Pure WC Sintered by Spark Plasma Sintering Method

Suppressing Pore-Boundary Separation During Spark Plasma Sintering of Tungsten

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Change in compositional fluctuation in Pb(Zr<SUB>x</SUB>Ti<SUB>1</SUB>−x)O<SUB>3</SUB> solid solution during spark plasma sintering

Effect of Tungsten Carbide on Densification and Mechanical Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Structure and Properties of Spark Plasma Sintered SiC Ceramics with Oxide Additives

In-Situ Synthesization of WC-6Co Cemented Carbides by SPS

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties