Abstract:The importance of micro-electromechanical systems (MEMS) for radio-frequency (RF) applications is rapidly growing. In RF mobile-communication systems, MEMS-based circuits enable a compact implementation, low power consumption and high RF performance, e.g., bulk-acoustic wave filters with low insertion loss and low noise or fast and reliable MEMS switches. However, the cross-hierarchical modelling of micro-electronic and micro-electromechanical constituents together in one multi-physical design process is still not as established as the design of integrated micro-electronic circuits, such as operational amplifiers. To close the gap between micro-electronics and micro-electromechanics, this paper presents an analytical approach towards the linear top-down design of MEMS resonators, based on their electrical specification, by the solution of the mechanical wave equation. In view of the central importance of thermal effects for the performance and stability of MEMS-based RF circuits, the temperature dependence was included in the model; the aim was to study the variations of the RF parameters of the resonators and to enable a temperature dependent MEMS oscillator simulation. The variations of the resonator parameters with respect to the ambient temperature were then verified by RF measurements in a vacuum chamber at temperatures between −35 ∘C and 85 ∘C. The systematic body of data revealed temperature coefficients of the resonant frequency between −26 ppm/K and −20 ppm/K, which are in good agreement with other data from the literature. Based on the MEMS resonator model derived, a MEMS oscillator was designed, simulated, and measured in a vacuum chamber yielding a measured temperature coefficient of the oscillation frequency of −26.3 ppm/K. The difference of the temperature coefficients of frequency of oscillator and resonator turned out to be mainly influenced by the limited Q-factor of the MEMS device. In both studies, the analytical model and the measurement showed very good agreement in terms of temperature dependence and the prediction of fabrication results of the resonators designed. This analytical modelling approach serves therefore as an important step towards the design and simulation of micro-electronics and micro-electromechanics in one uniform design process. Furthermore, temperature dependences of MEMS oscillators can now be studied by simulations instead of time-consuming and complex measurements.

Equivalent Circuit Model Extraction for a SAW Resonator: Below and above Room Temperature

On the Performance Evaluation of Commercial SAW Resonators by Means of a Direct and Reliable Equivalent-Circuit Extraction

Comparative Study of SAW Temperature Sensor Based on Different Piezoelectric Materials and Crystal Cuts for Passive Wireless Measurement

An Analytical Temperature-Dependent Design Model for Contour-Mode MEMS Resonators and Oscillators Verified by Measurements

Design and Analysis of a ZnO-quartz Structured SAW Resonator at 180Mhz Frequency

Note: Modified Pi-Type Butterworth-Van Dyke Model For Dual-Mode Lamb-Wave Resonator With Precise Two-Port Y-Parameter Characterizations

Geometry Characteristics and Wide Temperature Behavior of Silicon-Based GaN Surface Acoustic Wave Resonators with Ultrahigh Quality Factor

Equivalent Circuit Model of On-Wafer Interconnects for Cmos Rfics

Frequency-dependent equivalent modelling of broadband air-coupled transducers

Equivalent Circuit Analysis of 'U'-Shaped Split Ring Resonators

Temperature Characteristic of Ring Resonator in Polarization Maintaining Silica Optical Waveguide

Accurate Small-Signal Equivalent Circuit Modeling of Resonant Tunneling Diodes to 110 GHz

Experimental Analysis of Rayleigh and Sezawa Modes Resonance Frequencies in SAW Devices Manufactured on Sc0.3Al0.7N/Siâ€

A High Power Circuit Model of an FBAR Resonator for Use in Filter Design

Singly split single ring resonator: Fitting of lumped-element circuit model parameters and some aspects of resonator analysis and design

Power and temperature dependent model for High Q superconductors

A Modified PiBVD Model for LAMB Wave Resonator

Modal Analysis of Practical Quartz Resonators Using Finite Element Method

Temperature dependence of microwave losses in lumped-element resonators made from superconducting nanowires with high kinetic inductance

Design and Fabrication of an Surface Acoustic Wave Resonator Based on AlN/4H-SiC Material for Harsh Environments