Abstract:The present work investigates the effect of vanadium (V) micro-alloying addition on the microstructural evolution and mechanical properties of Al 354.0 alloy in as-cast and T6 condition. In particular, Al 354.0 with and without 0.3 wt.% V was developed by squeeze casting technique. The as-cast ingots were subjected to two types of heat treatment schedules, i.e., solution heat treatment at 495 °C for 8 h, followed by rapid water quenching and artificial aging at 190 °C for 2 h (T6), and solution heat treatment at 515 °C for 10 h, followed by rapid water quenching and artificial aging at 210 °C for 6 h (MT6), to modify the microstructure, morphology, and distribution of Al-, Cu-, and Mg-containing secondary phase(s). The phase and microstructure of unmodified and 0.3 wt.% V-modified alloys were analyzed using x-ray diffraction, optical microscopy, and field emission scanning electron microscopy coupled with energy-dispersive x-ray spectroscopy. Detailed analyses show that Al 2 Cu/Al 2 Cu(SiMg), Al 5 Si 2 Mg, and Al 2 Si were the strengthening phases in the unmodified alloy, whereas 0.3 wt.% V-modified alloy contains Al 10 V/Al 10 V(Mg), Al 3 Cu, Mg 2 Si, Al 4 Si, and Al(SiCuMg) as the primary strengthening phase(s). A subtle increase in the mechanical properties was evident in the 0.3 wt.% V-modified alloy compared to unmodified alloy at ambient temperature due to the presence of Al 10 V/Al 10 V(Mg) fine precipitates and Al(SiCuMg) intermetallic along the grain boundaries (GBs) preventing dislocation movement. T6 treatment resulted in a grain growth where needle/plate morphology of eutectic silicon was partially converted into spheroidal morphology, and Al 2 Cu/AlSiCuMg, Mg 2 Si, and Al 10 V/Al 10 V(Mg) intermetallic phases emerged increasing the tensile (0.3% V modified vs. unmodified; YS: ~ 287 vs. ~ 268 MPa, UTS: ~ 330 vs. ~ 334 MPa, elongation: ~ 1.5% vs. ~ 2.6%), compression (0.3% V modified vs. unmodified YS: ~ 497 vs. ~ 460 MPa, UCS: ~ 790 vs. ~ 776 MPa, compressive strain: ~ 40% vs. ~ 42%), and wear properties. However, modified T6 treatment (MT6) resulted in a grain growth where needle/plate morphology of eutectic silicon converted into spheroidal morphology, and Al 2 Cu partially and Mg 2 Si precipitates along the GBs were completely dissolved in the α -Al matrix by incipient melting improving the ductility (~5.9%) at the expense of yield strength (~104 MPa) and ultimate tensile strength (~218 MPa).

Effect of vanadium on Fe-rich phase, mechanical properties and thermal conductivity of hypoeutectic Al–Si alloy

Effect of vanadium element on the microstructure and mechanical properties of Cu-3.2Ti-0.2Fe alloys

MA-SPS-HIP Technique for Vanadium Alloys Preparation

Effect of Vanadium Micro-alloying on the Microstructure and Mechanical Properties of Stir Cast Al 354.0 Alloy

Effect of Vanadium Addition on the Microstructure, Hardness, and Wear Resistance of Al 0.5 CoCrCuFeNi High-Entropy Alloy

The influences of vanadium addition and temperature on the microstructure, and mechanical properties of Al 0.1 CoCrFeNiV x multi-principal element alloys

Revealing the influence of Fe on Fe-rich phases formation and mechanical properties of cast Al-Mg-Mn-Fe alloys

Effect of Low Cu Content and Heat Treatment on the Microstructure and Mechanical Properties of High-Vacuum Die-Cast AlSiMgMn Alloys

Synergistic Effect of Mo and V Addition on Al–Si Alloys Containing High Iron Impurity

Preparation and effect of vanadium addition on the mechanical properties of CoCrFeNiVx high-entropy alloy

Influence of Vanadium Precursor Powder Size on Microstructures and Properties of W–V Alloy

Effects of V on the Microstructure and Mechanical Properties of HfNbTaTiVx Refractory Multi-Principle Element Alloys: A Combined Experimental and Computational Study

Effect of element V on the as-cast microstructure and mechanical properties of Al0.4Co0.5VxFeNi high entropy alloys

A combinatorial assessment of microstructure and mechanical properties in AlCrCuFeNi2Vx concentrated alloys

Effect of vanadium element on the continuous precipitation behavior of Cu–3.2Ti–0.2Fe alloys

Influences of Zr and V Addition on the Crystal Chemistry of θ-Al13Fe4 and the Grain Refinement of α-Al in an Al-4Fe Alloy Based on Experiment and First-Principle Calculations

Effects of V addition on the solidification microstructures and room temperature compression properties of NiAl–Cr(Mo) hypereutectic alloy

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Influence of intermetallics and element concentrations on the performance of the heat treated HVDC AlSiMgMnCu alloys at nano-scale

Effects of vanadium content on the microstructure and tensile properties of NbTiV x Zr high-entropy alloys

The Effect of Vanadium Content Coupling with Heat Treatment Process on the Properties of Low-Vanadium Wear-Resistant Alloy