Abstract:The present work investigates the effect of vanadium (V) micro-alloying addition on the microstructural evolution and mechanical properties of Al 354.0 alloy in as-cast and T6 condition. In particular, Al 354.0 with and without 0.3 wt.% V was developed by squeeze casting technique. The as-cast ingots were subjected to two types of heat treatment schedules, i.e., solution heat treatment at 495 °C for 8 h, followed by rapid water quenching and artificial aging at 190 °C for 2 h (T6), and solution heat treatment at 515 °C for 10 h, followed by rapid water quenching and artificial aging at 210 °C for 6 h (MT6), to modify the microstructure, morphology, and distribution of Al-, Cu-, and Mg-containing secondary phase(s). The phase and microstructure of unmodified and 0.3 wt.% V-modified alloys were analyzed using x-ray diffraction, optical microscopy, and field emission scanning electron microscopy coupled with energy-dispersive x-ray spectroscopy. Detailed analyses show that Al 2 Cu/Al 2 Cu(SiMg), Al 5 Si 2 Mg, and Al 2 Si were the strengthening phases in the unmodified alloy, whereas 0.3 wt.% V-modified alloy contains Al 10 V/Al 10 V(Mg), Al 3 Cu, Mg 2 Si, Al 4 Si, and Al(SiCuMg) as the primary strengthening phase(s). A subtle increase in the mechanical properties was evident in the 0.3 wt.% V-modified alloy compared to unmodified alloy at ambient temperature due to the presence of Al 10 V/Al 10 V(Mg) fine precipitates and Al(SiCuMg) intermetallic along the grain boundaries (GBs) preventing dislocation movement. T6 treatment resulted in a grain growth where needle/plate morphology of eutectic silicon was partially converted into spheroidal morphology, and Al 2 Cu/AlSiCuMg, Mg 2 Si, and Al 10 V/Al 10 V(Mg) intermetallic phases emerged increasing the tensile (0.3% V modified vs. unmodified; YS: ~ 287 vs. ~ 268 MPa, UTS: ~ 330 vs. ~ 334 MPa, elongation: ~ 1.5% vs. ~ 2.6%), compression (0.3% V modified vs. unmodified YS: ~ 497 vs. ~ 460 MPa, UCS: ~ 790 vs. ~ 776 MPa, compressive strain: ~ 40% vs. ~ 42%), and wear properties. However, modified T6 treatment (MT6) resulted in a grain growth where needle/plate morphology of eutectic silicon converted into spheroidal morphology, and Al 2 Cu partially and Mg 2 Si precipitates along the GBs were completely dissolved in the α -Al matrix by incipient melting improving the ductility (~5.9%) at the expense of yield strength (~104 MPa) and ultimate tensile strength (~218 MPa).

Effect of vanadium element on the microstructure and mechanical properties of Cu-3.2Ti-0.2Fe alloys

Iinfluence of alloying elements and hydrogen and oxygen on tensile properties of vanadium alloys

Effect of vanadium element on the continuous precipitation behavior of Cu–3.2Ti–0.2Fe alloys

Effect of vanadium on Fe-rich phase, mechanical properties and thermal conductivity of hypoeutectic Al–Si alloy

Effect of Vanadium Micro-alloying on the Microstructure and Mechanical Properties of Stir Cast Al 354.0 Alloy

The Influence of Vanadium Element on the Microstructure and Mechanical Properties of (Feconi)100-Xvx High-Entropy Alloys

The effect of vanadium on the microstructure and mechanical properties of TiAl alloy fabricated by twin-wire directed energy deposition-arc

V 2.1 TiNi 0.4 Zr 0.06 Cu 0.03 M 0.10 (M=Cr, Co, Fe, Nb, Ta)储氢合金的微结构及电化学性能

Effects of V on the Microstructure and Mechanical Properties of HfNbTaTiVx Refractory Multi-Principle Element Alloys: A Combined Experimental and Computational Study

Microstructure and Electrochemical Properties of V_(2.1)TiNi_(0.4)Zr_(0.06)Cu_(0.03)M_(0.10)(M=Cr, Co, Fe, Nb, Ta) Hydrogen Storage Alloys

The influences of vanadium addition and temperature on the microstructure, and mechanical properties of Al 0.1 CoCrFeNiV x multi-principal element alloys

Effects of vanadium content on the microstructure and tensile properties of NbTiV x Zr high-entropy alloys

Effect of Vanadium Addition on the Microstructure, Hardness, and Wear Resistance of Al 0.5 CoCrCuFeNi High-Entropy Alloy

Achieving high strength and ductility in Fe-Mn-Al-C austenitic steel via vanadium microalloying and aging

Effects of V Element and Heat Treatment Process on Microstructure and Mechanical Properties of Additive Manufacturing of Titanium Aluminum Alloy Using Flux-Core Arc Welding Wire with TiH2 Powder

Effect Of Transition Metal Impurities On The Strength Of Grain Boundaries In Vanadium

Effect of V on the Microstructure and Brittle-to-ductile Transition of Directionally Solidified High-Nb TiAl Alloy

Effect of element V on the as-cast microstructure and mechanical properties of Al0.4Co0.5VxFeNi high entropy alloys

Effect of Vanadium on Properties of 18Cr-2Mo Ferritic Stainless Steel

Effect of V Addition on the Performance of Fe73.5Cu1B13Si9.5Nb3-V Soft Magnetic Alloys

Effects of Vanadium Microalloying and Intercritical Annealing on Yield Strength–Ductility Trade-Offs of Medium-Manganese Steels