Abstract:The high voltage bushing on the grid side of UHV converter transformer is located at the connection position between the grid side winding of converter transformer and the AC side system, which is the key equipment of UHVDC transmission system. In actual operation, the bushing will bear high temperature, large load current and additional load for a long time. In addition, due to the limitation of process level. During the rolling process of bushing capacitor core, there are inevitably some defects such as plate wrinkle, plate offset and unreliable grounding of the end plate. Under the long-term action of electricity, heat and stress, small defects are likely to develop into larger defects or even cause faults. Therefore, it is of great significance to study the influence of different defects on the electric field distribution in the bushing core and the partial discharge initial voltage (PDIV) of the bushing. On the basis of 550kV capacitive bushing, this paper designed and manufactured four scaled models. The rated working voltage of scaled models are 31.8kV. And the corresponding finite element simulation models are also established. The simulation results show that the wrinkle defect and offset defect will cause serious electric field distortion, resulting in a sharp increase of electric field at the defect. Ungrounded defects will completely change the distribution of electric field in the bushing, making the electric field concentrated in the insulating oil between the flange and the end plate. The measurement of PDIV shows that the wrinkle defect and offset defect can significantly reduce the PDIV which makes the bushing prone to PD at a lower voltage level and lead to fault. The initial voltage drop of ungrounded partial discharge is less, but the discharge amount is large. Therefore, the research of this paper has guiding significance for timely finding the original defects of bushing, preventing the development of defects, and solving the problem of frequent failure of converter bushing.

Cracking risk analysis and control for high‐voltage dry‐type valve‐side bushings

Numerical Simulation on Thermal Decomposition Process of Electric Arc Fault in Epoxy Resin Impregnated Paper Bushing

Insulation Degradation Characteristics and Phase-Field Simulation of Epoxy Resin for Valve-Side Bushing Under Strongly Coupled Electrothermal Field

Research on the Overheating Fault of HVDC Wall Bushing and Its Dignosis Strategies Based on CFD

Influence of Defects on the Electric Field Distribution of ±800kV Butt-type DC Wall Bushing

Influence Analysis on Defects in Bushing Core at Grid Side of Converter Transformer

Study on Partial Discharge Characteristics under the Thermal-Electrical Coupling Effect of Epoxy-impregnated Paper Insulation in High-Voltage Dry-type Valve Side Bushing

Degradation Characteristics of Insulation Near Aluminium Foil Edges Inside Dry‐type Bushing Cores under Electrothermal Compound Stress

Influence of Material Volume Conductivity on Electric Field and Surface Charge of RIP Valve-Side Bushing Core under DC Electro-Thermal Coupling Stress

Study of Thermal Field Distribution under Internal Crack Defects in the Valve-side Bushing of the Converter Transformer

Insulation Degradation of Epoxy Resin Impregnated Paper Bushing under Discharge Arc Ablation

Research on the Electrical Performance Design Criteria of the Adaptive Bushing Based on Nonlinear Materials

Investigation on distribution of electro-thermal coupled field and improved design of 1100 kV converter valve-side bushing

A Promising De-Ionized Water Cooling Based ERIP Bushing-I: Model Validation and High Cooling Efficiency of the Cooling Method

Temperature‐dependent electric field distribution in ±800 kV valve‐side bushing insulation for a converter transformer

Analysis of Electrical-Thermal-stress Characteristics for Eccentric Contact Strip in the Valve-Side Bushing of Converter Transformer

Electro-thermal comprehensive analysis method for defective bushings in HVDC converter transformer valve-side under multiple-frequency voltage and current harmonics

Research on the Deterioration Process of Electrical Contact Structure Inside the ±500 Kv Converter Transformer RIP Bushings and Its Prediction Strategy

Analysis and Disposal of Typical Breakdown Failure for Resin Impregnated Paper Bushing in the Valve Side of HVDC Converter Transformer

The Thermal Expansion Characteristics of Epoxy Resin/Crepe Paper Composites for High-Voltage Dc Bushing

Electrothermal Coupling Filed Calculation of 200 kV Adaptive Bushing