Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Heat conduction and thermal expansion of copper–graphite composite as a heat sink

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Electromagnetic and Thermal Characteristics of Graphite for Radiation Suppression in Wire-Bonded Package Heat Sink

Investigation of Graphite for Radiation Mitigation and Thermal Management in Heat Sink

Metal Injected Copper Carbon Nanotube Composite Material with High Thermal Conductivity and Low CTE for IGBT Power Modules

Study of Heat Dissipation Characteristics of Loop Heat Pipe with Heat Sink of Composite Material

Advanced composite materials with tailored thermal properties for heat sink applications

Fabrication, mechanical and thermal properties of tungsten-copper coated graphite flakes reinforced copper matrix composites

Study on radar electronic module cooling by using diamond/copper composites

Study on the structure and thermal properties of graphite/copper laminated composites assembled by Ti-containing active filler metals

Thermal interface material with graphene enhanced sintered copper for high temperature power electronics

Fabrication of diamond/copper composite thin plate based on a single-layer close packed diamond particles network for heat dissipation

Enhancement Effect of a Diamond Network on the Flow Boiling Heat Transfer Characteristics of a Diamond/Cu Heat Sink

Structure and Thermal Expansion of Cu-90 vol. % Graphite Composites

Thermal conductivity from hierarchical heat sinks using carbon nanotubes and graphene nanosheets

Mechanically strengthened graphene-Cu composite with reduced thermal expansion towards interconnect applications

In-situ synthesized graphene reinforced copper matrix composites with enhanced thermal properties and corrosion resistance

Sintering Behavior and Thermal Properties of Cu-Graphite Materials by a Spark Plasma Sintering Method

Research status of thermal conductivity in copper-carbon composite materials

Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites