Abstract:The problems of the recast layer, oxide layer, and heat-affected zone (HAZ) in conventional laser machining seriously impact material properties. Coaxial waterjet-assisted laser scanning machining (CWALSM) can reduce the conduction and accumulation of heat in laser machining by the high specific heat capacity of water and can realize the machining of nickel-based special alloy with almost no thermal damage. With the developed experimental setup, the laser ablation threshold and drilling experiments of the K4002 nickel-based special alloy were carried out. The effects of various factors on the thermal damage thickness were studied with an orthogonal experiment. Experimental results have indicated that the ablation threshold of K4002 nickel-based special alloy by a single pulse is 4.15 J/cm2. The orthogonal experiment results have shown that the effects of each factor on the thermal damage thickness are in the order of laser pulse frequency, waterjet speed, pulse overlap rate, laser pulse energy, and focal plane position. When the laser pulse energy is 0.21 mJ, the laser pulse frequency is 1 kHz, the pulse overlap is 55%, the focal plane position is 1 mm, and the waterjet speed is 6.98 m/s, no thermal damage machining can be achieved. In addition, a comparative experiment with laser drilling in the air was carried out under the same conditions. The results have shown that compared with laser machining in the air, the thermal damage thickness of CWALSM is smaller than 1 μm, and the hole taper is reduced by 106%. There is no accumulation and burr around the hole entrance, and the thermal damage thickness range is 0–0.996 μm. Furthermore, the thermal damage thickness range of laser machining in the air is 0.499–2.394 μm. It has also been found that the thermal damage thickness is greatest at the entrance to the hole, decreasing as the distance from the entrance increases.

Investigation on efficiency and quality for ultrashort pulsed laser ablation of nickel-based single crystal alloy DD6

Numerical Simulation on Pulsed Laser Ablation of the Single-Crystal Superalloy Considering Material Moving Front and Effect of Comprehensive Heat Dissipation

Study on Ablation Characteristics of Femyosecond Laser Nanoscale Processing for Aluminum Nitride and LeadZirconate Titanate Ceramics

Ablation enhancement of metal in ultrashort double-pulse experiments

Mechanisms of femtosecond laser ablation of Ni3Al: Molecular dynamics study

Towards obtaining high-quality surfaces with nanometric finish by femtosecond laser ablation: A case study on coppers

Fundamental 3D simulation of the femtosecond laser ablation for cooling hole drilling on Ni and Fe based aero-engine components

Research on Finite Element Simulation and Recrystallization of Laser Shock Peened Nickel-Based Single-Crystal Superalloy

Effect of Geometry Measurements on Characteristics of Femtosecond Laser Ablation of HR4 Nickel Alloy

Optimization of Femtosecond Laser Drilling Process for DD6 Single Crystal Alloy

Effect of hot electron blast force on ultrafast laser ablation of nickel thin film (vol 54, pg 1737, 2015)

Experimental Study on Coaxial Waterjet-Assisted Laser Scanning Machining of Nickel-Based Special Alloy

Numerical simulation and experimental analysis on nanosecond laser ablation of titanium alloy

Molecular dynamics study of the short laser pulse ablation: quality and efficiency in production

Research on the mechanism of DD6 single crystal superalloy wear resistance improvement by femtosecond laser modification

Kinetic Evolution of Laser Ablating Alloy Materials

Numerical simulation study of ultraviolet nanosecond laser ablation of Cu-Al2O3 dispersion strengthened alloys

DD6 single-crystal superalloy with thermal barrier coating in femtosecond laser percussion drilling

Femtosecond Laser-Induced Evolution of Surface Micro-Structure in Depth Direction of Nickel-Based Alloy

Experimental and numerical investigation on the ablation mechanism of Al2O3/Al2O3-CMCs under continuous-wave laser irradiation

Investigation on the ablation behavior of cemented tungsten carbide by a nanosecond UV laser