Abstract:One of the critical steps in total knee arthroplasty is femoral component positioning and sizing. Historically, there was wider variability between femoral component sizes, necessitating the concepts of anterior referencing (AR) and posterior referencing (PR). With the introduction of smaller increments between sizes, the concept of anatomic referencing has been introduced to replace AR and PR. The intent of this study was to validate the concept of anatomic referencing and show that with 2 mm increments in femoral sizes, the femoral component can be placed flush to the anterior cortex while maintaining posterior condylar offset (PCO). Digital surface models were created using 515 femurs from an established computed tomography database. Virtual bone resections, component sizing and placement were performed assuming neutral mechanical axis and a cartilage thickness of 2 mm. The appropriately sized femoral component, which had 2 mm incremental sizes, was placed flush with the anterior cortex with restoration of the PCO. The anterior–posterior distance from the posterior surface of the component to the medial and lateral surfaces of the posterior condylar cartilage were measured. The medial condyle was the limiting condyle in the majority of cases (73%). The average medial gap after appropriate femoral component matching was 0.6 mm (0.39–1.41 mm) across all sizes. The overall average condylar gap was 1.02 mm. The most common femoral component was a size 7 (57.2 mm) and the average femoral AP width was 55.9 mm. Anatomic referencing with an implant system that has 2-mm increments in femoral component sizing provides an alternative to AR and PR without compromise. Anatomic referencing allows for perfect alignment of the anterior flange of the femoral component to the anterior cortex of the femur while restoring the native PCO to within 1 mm. This avoids having to choose between AR or PR when in between femoral sizes. Received: 12 October 2023 Accepted: 07 January 2024 Accepted Manuscript online: 08 January 2024 Article published online: 27 February 2024 © 2024. Thieme. All rights reserved. Thieme Medical Publishers, Inc. 333 Seventh Avenue, 18th Floor, New York, NY 10001, USA

Variation of Femoral Component Size by Reference Points and Target Alignments in Total Knee Arthroplasty

An Evaluation of Anatomic Referencing for Femoral Component Sizing Using Computed Tomography-Based Computer Modeling

Tibial morphology of symptomatic osteoarthritic knees varies according to location: a retrospective observational study in Japanese patients

Variability of the femoral mechanical-anatomical axis angle and its implications in primary and revision total knee arthroplasty

Intraoperative anthropomorphic study of anterior femoral condyles compared with sizing of femoral arthroplasty

Effect of joint line orientation parameters on initial bone resection in mechanically aligned total knee arthroplasty: a retrospective clinicoradiological correlation study

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

Optimal Flexion for the Femoral Component in TKR: A Study of Angle Between Mechanical Axis and Distal Anatomic Intramedullary Axis Using 3D Reconstructed CT Scans in 407 Osteoarthritic Knees Studied in India

The accuracy of bony resection and component size planning of total knee arthroplasty assisted with a novel designed patient-specific instrumentation

Asymmetry of Posterior Condyles in Resection Plane and Axial Curvature for Total Knee Arthroplasty

Guidelines for Instrumentation for Total Knee Replacement Based on Frontal Plane Radiographs.

An MRI-Based Correlation Study Investigating the Effect of Varying Posterior Femoral Condyle Angles on the Patellofemoral Joint

Influence of femoral intramedullary guides on the limb alignment in total knee arthroplasty

High three‐dimensional accuracy of component placement and lower limb alignment using a robotic arm‐assisted system and gap‐balancing instrument in total knee arthroplasty

Preoperative evaluation of femoral and tibial sagittal alignment in robotic-assisted and conventional total knee arthroplasty and consequences for practice

Three-Dimensional Bowing Measurement of Distal Femur at Actual Size and Clinical Implications of Total Knee Arthroplasty

Accuracy of total knee arthroplasty using the modified gap technique based on the bone gap: an evaluation of the bone gap with a distal femoral trial component

Excessive flexed position of the femoral component causes abnormal kinematics and joint contact/ ligament forces in total knee arthroplasty

Influence of the angle between tibial and prosthesis mechanical axes on tibial bone remodeling in total knee arthroplasty

Finite element study of stress distribution in medial UKA under varied lower limb alignment

Variability of three-dimensional knee morphology cannot be effectively assessed using a coronal plane knee alignment classification in total knee arthroplasty patients