Abstract:Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.

Preparation of a poly(L-lactic acid) braided stent with high radial force

Regulating mechanical performance of poly (l-lactide acid) stent by the combined effects of heat and aqueous media

A hazardous boundary of Poly(L-lactic acid) braided stent design: Limited elastic deformability of polymer materials

A biodegradable polymer stent with high radial performance: Potential for treatment of portal vein stenosis

Design and characterization of PLLA stents with Z-structure

Computational and Experimental Investigation into Mechanical Performances of Poly-L-Lactide Acid (PLLA) Coronary Stents

Improved Mechanical Properties of Poly( L ‐lactic Acid) Stent Coated by Poly( D , L ‐lactic Acid) and Poly( L ‐lactic‐co‐glycolic Acid) Biopolymer Blend

Stereocomplex Poly(lactic Acid) Vascular Stents by 3d‐printing with Long Chain Branching Structures: Toward Desirable Crystallization Properties and Mechanical Performance

3D printed peripheral vascular stents based on degradable poly(trimethylene carbonate-b-(L-lactide-ran-glycolide)) terpolymer

A comparative in vitro study of distinct and novel stent geometries on mechanical performances of poly‐L‐lactic acid cardiovascular stents

<scp>3D</scp> printed peripheral vascular stents based on degradable poly(<scp>trimethylene carbonate‐b‐(L‐lactide‐ran‐glycolide)</scp>) terpolymer

Achieving high mechanical properties of biodegradable vascular stents by four-axis 3D printing system and heat treatment

Study on the Extrusion Molding Process of Polylactic Acid Micro Tubes for Biodegradable Vascular Stents

Failure signal of high orientation Poly(L-lactic acid) monofilament for self-expanding stent during lifetime: Disappeared amorphous connections

Braided Bioresorbable Cardiovascular Stents Mechanically Reinforced by Axial Runners.

A study of a biodegradable braided Mg stent for biliary reconstruction

Improving Mechanical Properties and Biocompatibilities by Highly Oriented Long Chain Branching Poly(lactic Acid) with Bionic Surface Structures

Annealing-induced oriented crystallization and its influence on the mechanical responses in the melt-spun monofilament of poly(L-lactide)

Shape memory properties of 3D‐printed self‐expandable poly(lactic acid) vascular stents with long‐chain branched structures

Preparation and Characterization of High-Melt-Strength Polylactide with Long-Chain Branched Structure Through Γ-Radiation-induced Chemical Reactions

High-Performance Self-Expanding NiTi Stents Manufactured by Laser Powder Bed Fusion