Abstract:The shape memory properties (SMP) of long‐chain branched poly(lactic acid) (b‐PLA) vascular stent prepared through 3D‐printed technologies are studied by comparison with PLA. SMP is expected to endow vascular stent smart properties of self‐expanding stent, which could self‐expand and support the stenosis after reaching the lesion. The shape recovery rate of the b‐PLA samples at 60°C reaches to 93%, which is much higher than that of the PLA samples with 26%. The two‐cycle deformation‐recovery test of dynamic mechanical analysis (DMA) shows that the shape recovery rate of b‐PLA samples at 60°C reaches 98% in the first and second cycle, suggesting the good SMP. Meanwhile, the 3D‐printed b‐PLA vascular stent could recover to initial shape within 22 s, while the PLA vascular stent could not recover to initial shape after shape deformation at 60°C. Furthermore, Two‐dimensional wide‐angle X‐ray diffraction analysis (2D‐WXRD) diffraction results confirm that both PLA and b‐PLA samples exhibit two bright diffraction spots of (200)/(100) plane, and 2D‐SAXS scattering patterns changed from uniform scattering rings to the spindle‐shaped pattern after shape deformation. After shape recovery at 60°C, the 2D‐WXRD diffraction and two‐dimensional small‐angle X‐ray scattering analysis (2D‐SAXS) scattering patterns of the PLA samples remain no change, while b‐PLA samples recover to initial patterns and exhibit diffuse diffraction rings and uniform scattering rings, respectively, long period (Lac) decrease and lamellae thickness (Lc) maintain constant. The above results verify the excellent SMP of b‐PLA vascular stent as well as self‐expandable properties, which mainly ascribing to the combined action of branched entanglement points and lamellae as stationary phase. Besides, cell counting kit‐8 (CCK‐8) assays, cell live/dead staining and cell nuclei/cytoskeleton staining prove the good cell compatibility of b‐PLA stent before and after SMP.

Achieving high mechanical properties of biodegradable vascular stents by four-axis 3D printing system and heat treatment

3D Printing and Characterization of the Biodegradable Vascular Stent

Development of Three-Dimensionally Printed Vascular Stents of Bioresorbable Poly(l-Lactide-co-caprolactone).

3D printed peripheral vascular stents based on degradable poly(trimethylene carbonate-b-(L-lactide-ran-glycolide)) terpolymer

Preparation of 4D Printed Peripheral Vascular Stent and Its Degradation Behavior under Fluid Shear Stress after Deployment

Mechanical Property of Thermoplastic Polyurethane Vascular Stents Fabricated by Fused Filament Fabrication

<scp>3D</scp> printed peripheral vascular stents based on degradable poly(<scp>trimethylene carbonate‐b‐(L‐lactide‐ran‐glycolide)</scp>) terpolymer

Heat-setting Effects on Physical and Mechanical Properties of Prototyped Biodegradable Stents

Regulating mechanical performance of poly (l-lactide acid) stent by the combined effects of heat and aqueous media

Experimental Study of Polymeric Stent Fabrication Using Homemade 3D Printing System

Thermo-Mechanical Characterization of 4D-Printed Biodegradable Shape-Memory Scaffolds Using Four-Axis 3D-Printing System

Shape memory properties of 3D‐printed self‐expandable poly(lactic acid) vascular stents with long‐chain branched structures

Crystallization and Biocompatibility Enhancement of 3D-Printed Poly(l-Lactide) Vascular Stents with Long Chain Branching Structures

3D Printing of Biodegradable Polymer Vascular Stents: A Review

The Effect of Intrinsic Characteristics on Mechanical Properties of Poly(l-Lactic Acid) Bioresorbable Vascular Stents.

Overview of Degradable Polymer Materials Suitable for 3D Printing Bio-stent

Direct 3D Printing of Thin-Walled Cardiovascular Stents with Negative Poisson’s Ratio (NPR) Structure and Functional Metallic Coating

Mechanical Properties and Degradation of Drug Eluted Bioresorbable Vascular Scaffolds Prepared by Three-Dimensional Printing Technology

Enhanced Mechanical Properties of Poly(l‐lactide) Braided Stent with Six‐arm Poly(l‐lactide‐co‐ε‐caprolactone) Coating Cross‐linked by Hexamethylene Diisocyanate

Optimization of 3D Printing Parameters of Polylactic-Co-Glycolic Acid-Based Biodegradable Antibacterial Materials Using Fused Deposition Modeling

Direct 3D printing of thin-walled cardiovascular stents with negative Poisson's ratio (NPR) structure and functional metallic coating