Abstract:To control underwater acoustic radiation of ships and protect against detection, coatings are attached to the vibrating wet surface of the hulls. Coatings with different pores or scatterers enclosed will attenuate vibration and suppress sound radiation with different mechanisms. However, there are very few experimental studies concerning vibration measurement of a coated structure in water, mainly due to the water environment. A compromised way to reveal the attenuation mechanism is to measure the vibration in an anechoic chamber. A stiffened plate covered by a rubber coating with multi-layered periodic porous is measured by a LDV scanning system in this study, which is aimed to minimize added mass effect of contact measurement. Comparative measurements on bare stiffened plate and stiffened plate covered with solid rubber are also carried out. Vibration transmission from the stiffened plate to the coatings as well as vibration modes on the radiating surface for the three tested objects is obtained. The vibration and sound attenuation mechanism of the proposed rubber coating is unveiled. To control underwater sound radiation of ships or submarines, acoustic coatings are developed, which is covered on the wet surface of hulls to reduce vibration or attenuate under-water acoustic radiation. Acoustic coatings can be classified into anechoic layer, decoupling layer, damping layer and the like. The main functions of anechoic layer are absorbing the incident acoustic waves for protecting against detection by active sonar. Decoupling layer isolates the fluid from the vibrating of the structure to reduce vibration and to attenuate sound radiation. Damping layer usually employed to reduce vibration. This investigation is concentrated on a layer which is designed to serve the sound and vibration insulation purpose, aiming at lowering the underwater sound radiation. For the purpose of underwater acoustic attenuation, the material should be compatible with water in terms of the acoustic impedance. Use of multilayer absorbers has become increasingly important in noise abatement. These layers are made of rubber material for its convenience of manufacturing and prominent damping. The solid rubber is not an ideal one because of its impedance match with that of water and the artificial rubber is proved to be the best. Therefore, the rubber material is designed with internal structures. Among them, two kinds of internal structures are studied extensively. One is with voids filled with air; the other one is cavities filled with scatterers (1). The vibration and sound insulation mechanisms are different for them. Some of the studies are summarized as follows. Maidanik and Tucker (2) studied the relations between coupled vibration and sound radiation for coated panels immersed in fluid media. Foin et al. (3) presented a coupled model to study the vibration and acoustic response of a rectangular plate covered by a decoupling coating and immersed in a heavy acoustic fluid. Berry et al. (4) analyzed the vibroacoustic of a finite rectangular plate covered with a layer of decoupling material and immersed in a heavy fluid based on three-dimensional theory of elasticity. Tao (5) built the vibroacoustic coupled model to predict the noise reduction performance of an infinite bare plate covered with a void decoupling layer. From the literatures above, it can be seen

RADIATION DAMPING IN PLATES, INDUCED BY POROUS MEDIA

Experimental and Frequency-Domain Study of Acoustic Damping of Single-Layer Perforated Plates

Effects of structural damping on acoustic scattering by flexible plates

An Experimental Study of Particle Damping for Beams and Plates

Experimental and Theoretical Analysis for a Fluid-Loaded, Simply Supported Plate Covered by a Damping and Decoupling Composite Acoustic Coating

Vibration and acoustic radiation control of a panel with piezoelectric oscillators.

The effect of ribs on the sound radiation directivity of rectangular plates

Sound radiation from plates with elastic boundary conditions embedded in an infinite perforated rigid baffle

Structural vibration damping by the use of poro-elastic layers: a summary

Sound Radiation from a Water Filled Pipe with an Attached Plate

Sound Radiation of Orthogonally Rib-Stiffened Sandwich Structures with Cavity Absorption

Sound radiation of parallelly stiffened plates under convected harmonic pressure excitation

An Analytical Study of the Vibroacoustic Response of a Ribbed Plate

Erratum to “A Novel Predicting Method of Vibration and Acoustic Radiation for Rectangular Plate with Particle Dampers”

LDV-based Vibration Measurement of a Stiffened Plate Covered by a Rubber Coating with Multi-Layered Periodic Porous in Air

MODELING AND DESIGN METHODOLOGIES FOR SOUND ABSORBING POROUS MATERIALS WHEN USED AS LAYERED VIBRATION DAMPERS

Non-obstructive Particle Damping Using Principles of Gas-Solid Flows

Structural vibration reduction achieved by lightweight porous layers through the near-field damping effect: A technical summary

Design and optimization of lightweight porous damping treatments

Attenuation Effects of Perforated Plates with Heterogeneously Distributed Holes on Combustion Instability in a Spray Flame Combustor

Investigation of vibro-acoustic characteristics of FRP plates with porous foam core