Abstract:Herein, a family of thiourea containing silicone-based photoresins suitable for creating silicone objects with excellent elasticity was developed for use in conventional digital light processing 3D printers. Rapid manufacturing of silicone products is highly desirable for small-volume manufacturing, especially for the application of customer-specific medical devices. However, because of their intrinsic high viscosity and lack of intermolecular interactions, 3D printing with silicone remains an ongoing challenge as suitable resins are not commercially available. To improve the elasticity of 3D-printed silicones, dynamic noncovalent intermolecular interactions between polymer chains were increased through the introduction of thiourea groups. Furthermore, a molecular design strategy was implemented based on utilizing "oligomeric" and "polymeric" PDMS units to adjust the ratio of thiourea segments. The cured silicone elastomer developed here displayed a maximum elongation of up to 1000% under tensile load and excellent cyclic compression durability. Moreover, this approach allowed for the 3D printing of PDMS-based objects with complex microarchitectures, high resolution, excellent surface finishing, and low cytotoxicity. The silicone thiourea resins have potential application in medical devices, wearable devices, and soft robotics.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsapm.1c00260?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsapm.1c00260</a>.Polymerization data of PDMS–thiourea polymers, <sup>1</sup>H NMR spectra of a typical PDMS–thiourea polymer, mechanical properties of cured silicones, representative photographs of printed parts, and cell morphological data for MTS assay (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_001.pdf">PDF</a>)Movie S1 showing the cyclic tensile of our cured silicone (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_002.avi">AVI</a>)Movies S2 and S3 showing the stretchability of the printed part (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_003.avi">AVI</a>) (<a class="ext-link" href="/doi/suppl/10.1021/acsapm.1c00260/suppl_file/ap1c00260_si_004.avi">AVI</a>)This article has not yet been cited by other publications.

PDMS Curing Inhibition on 3D-Printed Molds: Why? Also, How to Avoid It?

3D printed mold leachates in PDMS microfluidic devices

3D printing of release-agent retaining molds

Post‐Print Processing to Minimize Cytotoxicity of 3D‐Printed Photopolymer Resins for Biomedical Applications

3D Printing by Multiphase Silicone/Water Capillary Inks

Mitigation and control of the overcuring effect in mask projection micro-stereolithography

Solving curing-protocol-dependent shape errors in PDMS replication

Effects of post-curing duration on the mechanical properties of complex 3D printed geometrical parts

Functional Materials for DLP-SLA 3D Printing Using Thiol–Acrylate Chemistry: Resin Design and Postprint Applications

Systematically Studying Dissolution Process of 3D Printed Acrylonitrile Butadiene Styrene (ABS) Mold for Creation of Complex and Fully Transparent Polydimethylsiloxane (PDMS) Fluidic Devices

Digital Light Processing 3D Printing of PDMS-Based Soft and Elastic Materials with Tunable Mechanical Properties

Optimization of Curing Behavior of Si3N4 UV Resin for Photopolymerization 3D Printing

Postpolymerization of a 3D-printed denture base polymer: Impact of post-curing methods on surface characteristics, flexural strength, and cytotoxicity

Highly Efficient Consolidation of Mesoporous Silica Microstructures Using Photonic Curing

Fabrication of 3D-printed molds for polydimethylsiloxane-based microfluidic devices using a liquid crystal display-based vat photopolymerization process: printing quality, drug response and 3D invasion cell culture assays

Urethane dimethacrylate-based photopolymerizable resins for stereolithography 3D printing: A physicochemical characterisation and biocompatibility evaluation

3D Printing of PDMS Improves Its Mechanical and Cell Adhesion Properties

Novel Dual-Curing Process for a Stereolithographically Printed Part Triggers a Remarkably Improved Interlayer Adhesion and Excellent Mechanical Properties

A Comparative Study on 3D Printed Silicone-Epoxy/acrylate Hybrid Polymers Via Pure Photopolymerization and Dual-Curing Mechanisms

Plasmonic and Semiconductor Nanoparticles Interfere with Stereolithographic 3D Printing

Effect of resin composition on cure depth, dimensional accuracy, and surface roughness in Al2O3 stereolithographic 3D printing