Abstract:Axial-load fatigue-crack-propagation tests were conducted on 12 in. (305 mm) wide sheet specimens made of 7075-T6 aluminum alloy. These tests were made at stress ratios R (ratio of the minimum stress to the maximum stress) ranging from −1.0 to 0.8 and at maximum stress levels ranging from 5 to 50 ksi (34–340 MN/m2) to study the effects of stress ratio on fatigue-crack growth. The fatigue-crack-propagation data were analyzed using Paris' stress-intensity analysis. The data from tests at negative R values fell into a relatively narrow scatterband along with the results from the R = 0 tests on a plot of rate against stressintensity range. Apparently, the compression portion of the loading cycle did not significantly affect crack growth in these tests. The data from tests at different positive stress ratios fell into discrete bands on these plots. These bands varied systematically with R, that is, the higher the stress ratio at a given value of ΔK, the higher the rate of fatigue-crack growth. This spread in rates was small at the lower stress-intensity range, but became progressively larger as the stress-intensity range was increased.Semiempirical equations developed by Forman et al., by Broek and Schijve, and by Paris were fitted to the data from this investigation using a least squares fit. Forman's equation gave the best fit to the data.The fracture surfaces of the specimens changed from the normal mode to a shear mode within a reasonably narrow range of crack growth rates for all R values. The stress-intensity range at transition was approximately a constant for tests at negative stress ratios. Forman's equation adequately represented the variation between the stress ratio and the stress-intensity range at positive stress ratios.

The effect of frequency on fatigue crack propagation rate and striation spacing in 2024-T3 aluminium alloy and SM-50 steel

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

DIC-based Studies of the Overloading Effects on the Fatigue Crack Propagation Behavior of Ti-6Al-4V ELI Alloy

Influence of Environment and Creep on Fatigue Crack Growth in a High Temperature Aluminum Alloy 8009

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Analyses of the fatigue crack propagation process and stress ratio effects using the two parameter method

Effect of stress ratio on fatigue-crack growth in 7075-T6 aluminum-alloy sheet

Interpretation of Frequency Effect for High-Strength Steels with Three Different Strength Levels via Crystal Plasticity Finite Element Method

Effect Of Stress Concentration Factor And Residual Stresses On The Delay Of Fatigue Crack Propagation

On the Study of Fatigue Crack Propagation in the Time Domain

An analysis of fatigue crack features at various crack lengths through mating fracture surface pairs

Effect of loading conditions on short fatigue crack propagation behaviours in cast Al Si alloys

In-situ experimental study on the fatigue crack propagation behavior of 7075-T6 and 2024-T3 aluminium alloys under variable amplitude loading and retardation model modification

Effect of Cyclic Load Frequency on the Fatigue Crack Nucleation and Growth of Annealed and Prestrained Austenitic SS 304

Effect of Loading Methods on the Fatigue Properties of Dissimilar Al/Steel Keyhole-Free FSSW Joints

Effect of laser alloying on the fatigue crack growth rate

Effect of Compressive Mean Stress on the Fatigue Strength and Crack Growth Characteristics of Aluminum Alloys

Effect of Pre-Strain on Fatigue Strength of Aluminum Alloy 5052.

Synergistic Effect of Environmental Media and Stress on the Fatigue Fracture Behaviour of Aluminium Alloys

Effect of overload occurence frequency on fatigue crack growth rate of steel A537

Experimental investigation of overload effects on fatigue crack growth behaviour of 7050‐T7451 aluminium alloy