Abstract:Problem statement. The selective laser melting method is a promising technology for the production of parts from heat-resistant alloys. Traditional methods of manufacturing such parts require additional technological equipment and processing, which increases the time of production preparation and, as a result, to the creation of a large number of raw materials. Selective laser melting allows you to produce parts of a complex configuration without the need for additional equipment. Molding of parts using additive technologies, which ensure a reduction in product preparation time, mechanical processing operations, and an increase in the efficiency of material use. Their application in the technological cycle of manufacturing products is an urgent task today. However, before the introduction into the technological process of forming products from heat-resistant alloys by the selective laser melting method, it is necessary to carry out a comprehensive analysis of the mechanical and technological characteristics of the material and its microstructure, which affects the final properties of the parts. The purpose of the article. Investigation of the possibility of implementing the selective laser melting method for the production of parts from strong alloys, analysis of the mechanical characteristics of the material, as well as the microstructure, which affects the final properties of the parts. Conclusions. Studies have shown that the selective laser melting method is effective for the production of complex parts from heat-resistant alloys. The obtained data on the mechanical properties after heat treatment of the Inconel718 alloy demonstrate its compliance with the requirements of the AMS 5662 standard and its suitability for working under extreme conditions. In the microstructure, highlighted features are revealed, which are characteristic of the selective laser melting method, as well as the presence of visible tracks and a special texture − elongated grains in the direction of growing parts. Research points to the potential of additive technologies in improving technological processes and properties of alloys for the production of heat-resistant alloy parts.

PRODUCTION OF MMC BASED ON VZh159 ALLOY BY SELECTIVE LASER MELTING

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Creation of an aluminum matrix composite with a core-shell carbide reinforcing phase with improved strength characteristics using selective laser sintering

Selective Laser Melting of Al-Based Matrix Composites with Al2O3 Reinforcement: Features and Advantages

Phase Composition, Microstructure and Mechanical Properties of Zr57Cu15Ni10Nb5 Alloy Obtained by Selective Laser Melting

Structure and properties of a cobalt-chromium-molybdenum alloy obtained by selective laser melting

STUDY OF THE STRUCTURE AND MECHANICAL PROPERTIES OF SAMPLES PRODUCED BY THE METHOD OF SELECTIVE LASER MELTING FROM METALLIC POWDER OF HEAT-RESISTANT ALLOY VZH-159 (KhN58MBYu)

Microstructural, Mechanical, and Tribological Characterization of Selective Laser Melted CoCrMo Alloy under Different Heat Treatment Conditions and Hot Isostatic Pressing

INVESTIGATION OF THE STRUCTURE AND PROPERTIES OF FERROUS NICKEL ALLOYS AFTER MOLDING BY SELECTIVE LASER MELTING

From Ni–P Metastable Alloy Nanoparticles to Bulk Submicrometer Grain-Sized MMCs with Tunable Mechanical and Magnetic Properties

Microstructural, Mechanical and Tribological Behaviour of NiTi/SiC/ZrO2 Reinforced Aluminium 6061 Hybrid MMCs

Fabrication of AA2024/SiCp Metal Matrix Composite by Mechanical Alloying

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Analysis of a squeeze cast magnesium alloy with Aluminium metal matrix composites

Selective Laser Melting to Manufacture “In Situ” Metal Matrix Composites: A Review

The Influence of Selected Laser Engraving Parameters on Surface Conditions of Hybrid Metal Matrix Composites

Mechanical Behavior of a Medium-Entropy Fe65(CoNi)25Cr9.5C0.5 Alloy Produced by Selective Laser Melting

Exploring the mechanical, metallurgical, and fracture characteristics of hybrid-reinforced magnesium metal matrix composite synthesized via friction stir processing route

Additive manufacturing of micro/nano multiphase synergistically reinforced Ti-55Al-7.5Nb with a reticular boundary precipitate via direct laser deposition

Fabrication And Characterization of Al/ Sic/ Gr Hybrid Metal Matrix Composite Fabricated By Powder Metallurgy

Micro-laminated CoCrFeMnNi−TiN p /CoCrFeMnNi high-entropy alloy matrix composite with bimodal grain structure via multi-material selective laser melting (MM-SLM) additive manufacturing