Abstract:High-manganese steels, due to their unique combination of strength and elongation, have been widely used in aerospace, petrochemical and rail transportation. However, a prevalent challenge in advancing the utilization of high-manganese steel is the need for corresponding welding consumables. The deformation mechanism of high-manganese steel encompasses three primary mechanisms: martensitic phase transformation, twinning and dislocation movement. The stacking fault energy (SFE) is a critical factor in determining the dominant deformation mechanism in high-manganese austenitic steels. Furthermore, the magnitude of the SFE is principally influenced by the alloying elements present and the temperature at which deformation occurs. Alloying elements can significantly influence the microstructure and mechanical properties of wire arc additive manufacturing (WAAM) of high-manganese steels. The metal powder-cored wire of high-manganese steel with full austenitic microstructure was designed in this paper. The effects of C, Mn and Cu on the microstructure, solute segregation and properties of WAAM of high-manganese steels were systematically investigated by optical microscopy, electron microscopy and mechanical testing. The influence of SFE on the microstructure characteristics and work hardening behaviour were also studied. The results showed that as an increase of the C content, the tensile strength and elongation of deposited metals were improved. The corresponding low-temperature impact toughness increased at first and then decreased. The highest value of impact toughness was 68.5 J with 0.79%C. As the Mn increased, the strength decreased, the elongation increased and the low-temperature impact toughness value displayed an initial increase followed by a subsequent decrease. With the increase of Cu, the yield strength and elongation improved significantly. The tensile strength exhibited a marginal initial increase followed by a decrease, whereas the change was not substantial. In contrast, the low-temperature impact toughness value showed a substantial increase followed by a decrease. The developed M3 wire containing 1.10%C-21%Mn-0.3%Cu possessed the optimum performance (yield strength of 551 MPa, tensile strength of 909 MPa, elongation at break of 30.2%, impact toughness value of 57.5J), with the good mechanical stability and low solidification cracking sensitivity.

Metallographic, Structural, and Mechanical Characterization of Weld Nuggets in Fe–Mn–Al–C Low‐Density Steels Microalloyed with Ti/B and Ce/La by Gas Tungsten Arc Welding Process

Estimation of Residual Stresses by Nanoindentation in an Experimental High Strength Microalloyed Steel Subjected to Rapid Thermal Cycles

Microstructure evolution and mechanical properties in a gas tungsten arc welded Fe42Mn28Co10Cr15Si5 metastable high entropy alloy

Tailoring the Microstructure of Coarse-Grained HAZ in Steel for Large Heat Input Welding: Effect of Ti–Mg–Ce–V Inclusion/Precipitation Particles

The Microstructure and Mechanical Properties of Welded Joints of Hot-Rolled and Post-Weld Solution-Treated Fe-12.5Mn-9.8Al-1.0C Low-Density Steel

Microstructural characterization and hardness of an electron beam welded low carbon Ni-Cr-Mo low alloy steel

Heat affected zone liquation cracking evaluation on FeMnAl alloys

Crucial Microstructural Features to Determine the Mechanical Properties of Welded Joints in a Cu-Containing Low-Carbon Low-Alloy Steel After Postweld Heat Treatment

Microstructure and mechanical properties of ultralow carbon high-strength steel weld metals with or without Cu-Nb addition

Microstructural Characterization and Grain Refinement of Ti-15 V-3Al-3Cr-3Sn Gas Tungsten Arc Welds by Ni- and Si-Modified Fillers

Inclusion Evolution Behavior of Ti-Mg Oxide Metallurgy Steel and Its Effect on a High Heat Input Welding HAZ

Microstructural evolution of a low-alloy steel / nickel superalloy dissimilar metal weld during post-weld heat treatment

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Solidification Cracking Restraining Mechanism of Al-Cu-Mg-Zn Alloy Welds Using Cold Metal Transfer Technique

Microstructural and mechanical characterization of electron beam welded low-nickel nitrogen-strengthened austenitic stainless steel

Effect of C-Mn-Cu on microstructure and properties of wire arc additive manufacturing of high-manganese steels

Investigations on weld joints of 7075 alloy with Al–5Mg–1Zn composite fillers by arc welding

Microstructure and mechanical properties of gas metal arc welded CoCrFeMnNi joints using a 308 stainless steel filler metal

Microstructure and Local Mechanical Properties of the Heat-Affected Zone of a Resistance Spot Welded Medium-Mn Steel