Abstract:Physically based constitutive equations incorporating the key microstructural mechanisms e.g. dislocations, grain size, etc, have been used widely to predict the stress-strain behaviour of alloys at plastic and viscoplastic conditions. This enables an accurate prediction of the formed geometry as well as the final underlying microstructures. However, these physically based constitutive equations have not been practically validated due to the lack of systematic experimental data at microscopic scale. This leads to a large number of unknown constants required to be determined through various optimization algorithms. The aim of this paper is to provide direct and systematic experimental data by revealing the dislocation (geometrically necessary one) density and grain size evolution of AA6082, which is a widely used high-strength aluminium alloy for automobile structural panels, as functions of strain, strain rate and temperature, and is the first-time using Electron Back Scattering Diffraction (EBSD) technique to visualize the microstructures during the hot deformation. The evolution of the dislocation accumulation during the hot tensile deformation at 300, 450, 530 degrees C using various strain rates (i.e. 1/s, 0.1/s, 0.01/s) was achieved. EBSD maps were analysed on samples submitted to a true strain level of similar to 0.1 and similar to 0.3 under each condition. These maps cover >3000 grains and enable to capture the statistical nature of the geometrically necessary dislocation densities during hot deformation. Despite the rapidly plateaued flow stress curves at high temperatures, a continuously increased average GND density was observed in AA6082 with the imposed true strain levels under all conditions. Dislocation channel structures were observed in the hot deformed samples. Dynamic recrystallization was also observed, which coupled with the GNDs and affected the hardening behaviour of the flow stress-strain curves. This work is the first study, using EBSD, to visualize the high temperature and high strain rate induced dislocation distributions over a relatively large area, providing valuable data that may be used for subsequently improving and calibrating the physically based material models.

Quantitative Study of Residual Strain and Geometrically Necessary Dislocation Density Using HR-EBSD Method

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Quantifying Geometrically Necessary Dislocation Density During Hot Deformation in AA6082 Al Alloy

Quantitative Evaluation of Dislocation Density in SUS316L Utilizing Non-Contact Microwave Reflection Method

Heterogeneous local plastic deformation of interstitial free steel revealed using in-situ tensile testing and high angular resolution electron backscatter diffraction

Resolving localized geometrically necessary dislocation densities in Al-Mg polycrystal via in situ EBSD

Local Residual Stress in Partially Recrystallized Iron Characterized Using High Resolution Electron Backscatter Diffraction

Precise Measurement of Strain Accommodation in a Mg-Gd-Y-Zn Alloy Using Cross-Correlation-based High Resolution EBSD

High Strain Gradient Plasticity Associated with Wedge Indentation into Face-Centered Cubic Single Crystals: Geometrically Necessary Dislocation Densities

Influence of Severe Straining and Strain Rate on the Evolution of Dislocation Structures During Micro-/Nanoindentation in High Entropy Lamellar Eutectics

Residual Elastic Stress–strain Field and Geometrically Necessary Dislocation Density Distribution Around Nano-Indentation in TA15 Titanium Alloy

Effect of deformation heterogeneity on development of geometrically necessary dislocation density in heterogeneous-structured CrMnFeCoNi high-entropy alloy

Local measurement of geometrically necessary dislocation densities and their strengthening effect in ultra-high deformed pearlite

Quantification of changes in lattice defect density in BCC iron during plastic deformation using electrical resistivity measurements

Automated Analysis Framework of Strain Partitioning and Deformation Mechanisms Via Multimodal Fusion and Computer Vision

HR-EBSD analysis of in situ stable crack growth at the micron scale

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

3D in-situ characterization of dislocation density in nickel-titanium shape memory alloys using high-energy diffraction microscopy

Diffraction-Based Multiscale Residual Strain Measurements

The effect of δ-hydride on the micromechanical deformation of Zircaloy-4 studied by in situ high angular resolution electron backscatter diffraction

Effects of Mechanical Deformation on Dislocation Density and Phase Partitioning in 4130 Steel