Abstract:One important challenge in producing high-speed steels (HSSs) by conventional route is how to improve their hot workability. In this work, the effect of high-temperature annealing on the microstructure evolution and hot deformation behavior of the as-cast high-nitrogen M42 HSS was studied. The results indicated that the as-cast microstructure of high-nitrogen M42 HSS mainly consisted of the dendrite cells of matrix, interdendritic network of M2C eutectic carbides, primary M(C,N) carbonitrides, and intradendritic fine M2C secondary carbides. After high-temperature annealing, M2C eutectic carbides were transformed into M6C and M(C,N) products via a diffusion-driven reaction of M2C + matrix → M6C + M(C,N), and M6C carbides were the dominant products. Initially, M6C and M(C,N) nucleated at the M2C/matrix interface, and then grew inward from outside. With increasing annealing temperature and time, the average length–width ratio of interdendritic mixed carbides of M2C and M6C gradually decreased. The full decomposition and breaking of M2C eutectic carbides in the as-cast high-nitrogen M42 HSS could be achieved by annealing at 1100 °C for 8 hours. Meanwhile, high-temperature annealing led to the decreased amount of intradendritic M2C secondary carbides and the formation of M6C carbides within the intradendritic region. The high-temperature annealed steel exhibited higher flow stress than the as-cast steel at most deformation conditions, but lower deformation activation energy. The macroscopic morphologies showed that the hot workability of the high-temperature annealed steel was evidently better than that of the as-cast steel, which could be attributed to its better deformation compatibility and more sufficient dynamic recrystallization (DRX). Moreover, high-temperature annealing treatment led to a more uniform carbide distribution after hot compression. Therefore, high-temperature annealing treatment may provide an opportunity to further maintain or even improve the competitiveness of HSS produced by conventional route compared with those by powder metallurgy.

Microstructural changes in as-cast M2 grade high speed steel during high temperature treatment

Evolving Mechanism of Eutectic Carbide in As-Cast AISI M2 High-Speed Steel at Elevated Temperature

Effect of RE-Al-N on Structures and Properties of M2 Cast High Speed Steel

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Effect of Tempering Conditions on Secondary Hardening of Carbides and Retained Austenite in Spray-Formed M42 High-Speed Steel

Microstructural changes of high speed steel powders during heating in vacuum

Microstructure Evolution and Mechanical Performance of Nickel Based Superalloy C1023 at Elevated Temperatures

High-Temperature Annealing Significantly Enhances Intrinsic Hot Workability of the As-cast High-Nitrogen M42 High-Speed Steel

Microstructure evolution and its impact on mechanical properties of a cobalt-based superalloy subjected to long-term heat-treatments

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Microstructure Evolution and Precipitation Strengthening Behaviour of Additively Manufactured High-speed Steels

Insight into the induction hardening behavior of a new 0.40% C microalloyed steel: Effects of initial microstructure and thermal cycles

Evolutions of Microstructure by Cerium Treatment in As‐Cast M2 High‐Speed Steel

Increasing Solidification Rate of M2 High-Speed Steel Ingot by Fusible Metal Mold

Effect of Heat Treatment on the Microstructural Heterogeneity and Abrasive Wear Behavior of ASTM A128 Grade C Steel

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

Effect of Microstructural Evolution on Mechanical Properties of Secondary Hardening Low‐carbon High‐alloy Bearing Steel

Effect of Heat Treatment on Structure and Properties of B Alloyed High Speed Steel for Rolling Mill Rolls

Microstructure and mechanical properties of M2 high speed steel produced by electron beam melting

Microstructural variations and mechanical properties of deep cryogenic treated AISI M35 high-speed steel tempered at various temperatures

Microstructural evolution in austenitic heat-resistant cast steel 35Cr25Ni12NNbRE during long-term service