Abstract:Although the use of 3D printing in civil engineering has grown in popularity, one of the primary challenges associated with it is the absence of steel bars inside the printed mortar. As a result, developing 3D printing mortar with ultra-high compressive, flexural, and tensile strengths is critical. In the present study, an ultra-high-performance mortar incorporating silica fume (SF) and graphene nanoplatelets (GNPs) was developed for 3D printing application. The concrete mixture added SF to the concrete mixture in the range between 0% and 20%, while GNPs were added as a partial replacement by cement weight from 0.5% to 2%. The flowability and the machinal properties of the proposed mortar, including compressive (CS), tensile (TS), and flexural strength (FS), were investigated and assessed. Microstructure analysis involving FESEM and EDX was also investigated and evaluated, while response surface methodology (RSM) was considered to predict and optimize the optimum value of GNPs and SF. Workability results show that the flowability is reduced when the amount of graphene increases. Based on the predicted and experimental results, ultra-high-strength mortar can be developed by including 1.5% of GNPs and 20% of SF, in which the CS jumped from 70.7 MPa to 133.3 MPa at the age of 28 days. The FS and TS were 20.66 MPa and 14.67 MPa compared to the control mix (9.75 MPa and 6.36 MPa), respectively. This favorable outcome was credited to the pozzolanic activity of SF and the effectiveness of GNPs in compacting the pores and bridging the cracks at the nanoscale level, which were verified by FE-SEM and EDX. In addition, the developed quadratic equations proved their accuracy in predicting and optimizing the mechanical properties with low error (less than 0.09) and high correlation (R2 > 0.97). It can be concluded that the current work is an important step forward in developing a 3D printing mortar. The lack of reinforcement in the printed mortar structure has been a considerable difficulty, and the SF and GNPs have increased the compressive, flexural, and tensile strengths of the mortar. Thus, these improvements will encourage the industry to utilize sustainable materials to produce more affordable housing.

Short-duration near-nozzle mixing for 3D concrete printing

Quick nozzle mixing technology for 3D printing foam concrete

Mechanisms of rheological modifiers for quick mixing method in 3D concrete printing

Surfactants to enable quick nozzle mixing in 3D concrete printing

Effect of Nanostructured Silica Additives on the Extrusion-Based 3D Concrete Printing Application

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Blending performance of helical static mixer used for twin-pipe 3D concrete printing

Development of concrete mixes for 3D printing using simple tools and techniques

D-optimal design of experiments applied to 3D high-performance concrete printing mix design

Micro/Nano additives in 3D printing concrete: Opportunities, challenges, and potential outlook in construction applications

Printability region for 3D concrete printing using slump and slump flow test

Investigation of the material mixtures and fiber addition for 3D concrete printing

Optimizing Concrete Mix Design for Application in 3D Printing Technology for the Construction Industry

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Tailoring Light-Weight Aggregates for Concrete 3D Printing Applications

Rheology and pumpability of mix suitable for extrusion-based concrete 3D printing – A review

Mix design, optimization and performance evaluation of extrusion-based 3D printable concrete

3D printing eco-friendly concrete containing under-utilised and waste solids as aggregates

Nozzle criteria for enhancing extrudability, buildability and interlayer bonding in 3D printing concrete

3D Printed Concrete: Fresh and Hardened Properties

Development of Ultra-High-Performance Silica Fume-Based Mortar Incorporating Graphene Nanoplatelets for 3-Dimensional Concrete Printing Application