Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Creep Mechanisms in Niobium-Silicide Based In-Situ Composites

Creep Mechanisms in Niobium-Silicide Based In-Situ Composites

High-Temperature Creep of Nb–Si In Situ Composites

Creep Mechanisms in High-Temperature In-Situ Composites

Modeling creep behavior of niobium silicide in-situ composites

New Insights of the Microcrack Initiation Induced by Mo Addition in Ni-based Single Crystal Superalloys During Creep at 900 °C

Tensile and Creep Properties of the Refractory Nb Base In-Situ Composite

Significantly Enhanced Creep Resistance of Low Volume Fraction In-Situ TiBw/Ti6Al4V Composites by Architectured Network Reinforcements

Creep Behavior and Deformation Mechanism of a Third-Generation Single Crystal Ni-Based Superalloy at 980 °C

Constructing Two-Scale Network Microstructure with Nano-Ti5si3 for Superhigh Creep Resistance

The balance of mechanical and environmental properties of a multielement niobium-niobium silicide-basedIn Situ composite

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Atomic models of the structure of niobium silicides in Nb–Si in situ composites

High temperature creep behavior of in situ synthesized MoSi2-30%SiC composite

Niobium enrichment and environmental enhancement of creep crack growth in nickel-base superalloys

Analyses of Eutectoid Phase Transformations in Nb–Silicide In Situ Composites

Grain Boundary Sliding-Induced Creep of Powder Metallurgically Produced Nb-20Si-23Ti-6Al-3Cr-4Hf

In Situ SEM Study of Creep Deformation Behavior of Nickel-Based Single-Crystal Superalloys

Microstructural and mechanical evaluation of Nb-silicide-based in situ composite at ultrahigh temperature

On the Microstructure and Properties of Nb-18Si-6Mo-5Al-5Cr-2.5W-1Hf Nb-Silicide Based Alloys with Ge, Sn and Ti Additions (at.%)

On the oxidation mechanism of niobium-base in situ composites