Abstract:A special treatment of platinum group metals (PGMs) leaching from spent automotive catalyst is shown in this paper. Leaching of crushing and grinding automotive catalyst scrap in hydrochloric acid with defined concentration, added nitric acid as oxidant, produced chloride solution of the platinum group metals, while catalyst substrate (Al 2 O 3) remained indissoluble. Cementation of the leached platinum group metals from solution was made by powered aluminum with suitable pH values. The precipitate obtained by cementation with Al-powder is mixture of the platinum group metals and surplus aluminum. The surplus aluminum can be removed by selected resolving with hydrochloric acid. The mixture of platinum group metals (Pt, Pd, and Rh) is obtained by this treatment. Separation between platinum group metals was done by well-known chemical processes. 1. INTRODUCTION Automotive catalysts have been extensively used for reducing the amount of unburned hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO x) from the exhaust gas emitted by automobiles. Platinum group metals (PGMs) have been used as catalytic agents because of their heat resistance and special catalytic activity. The content of total PGMs in automotive catalyst is about 0.5 to 2.0 g per kilogram. Autocatalyst essentially comprise a refractory oxide carrier on which two or more precious metals are dispersed in very low concentration. The worldwide demand of PGMs used for autocatalysts has increased with rapid motorization and the enforcement of stringent regulations for exhaust gas. In 2001, 37% of the worldwide demand for platinum, 72% of palladium and 85% of rhodium was for their use as automotive catalysts. In the year 2003, the overall demand of platinum was about 200 metric tons; 5% had to be met from stock in the last years because of lower primary and secondary production. Half of the produced platinum was used for catalysts in the automotive industry. From this, one third is covered by platinum out of secondary metallurgical processes [1,2]. Due to their scarcity and high price, the recovery of PGMs from spent automotive catalyst, generally called catalyst scrap, is a very important. The catalyst scrap generally consists of the surface layer with a high degree of porosity and the catalyst substrate (such as SiO 2 , Al 2 O 3 and CeO 2) with honeycomb structure. Ceramic materials were chosen for the initial monolith and they still dominate market. The preferred materials is called cordierite (synthetic cordierite has a composition approximating 2MgO, …

PACEPAC: A road dust as a certified reference material for the quality assurance in the analysis of Pt, Pd and Rh in environmental samples

Autocatalyst-derived platinum, palladium and rhodium (PGE) in infiltration basin and wetland sediments receiving urban runoff

Recovery of platinum group elements from waste material

Performance Parameters of Inductively Coupled Plasma Optical Emission Spectrometry and Graphite Furnace Atomic Absorption Spectrometry Techniques for Pd and Pt Determination in Automotive Catalysts

Platinum group element and cerium concentrations in roadside environments in Toronto, Canada

Comparison of palladium and platinum in environmental matrices: Palladium pollution by automobile emissions?

Platinum-group elements: quantification in collected exhaust fumes and studies of catalyst surfaces

Accumulation and distribution characteristics of platinum group elements in roadside dusts in Beijing, China

Importance of Automobile Exhaust Catalyst Emissions for the Deposition of Platinum, Palladium, and Rhodium in the Northern Hemisphere

An assessment of the inhalation bioaccessibility of platinum group elements in road dust using a simulated lung fluid

Mobility of traffic-related Pd and Pt species in soils evaluated by sequential extraction

In vitro investigations of platinum, palladium, and rhodium mobility in urban airborne particulate matter (PM10, PM2.5, and PM1) using simulated lung fluids

A simple and accurate method for the determination of Rh, Pd, and Pt in e-waste and spent automotive catalysts using HR-CS FAAS for assessing the value of secondary raw materials

Platinum group elements study in automobile catalysts and exhaust gas samples

Platinum, palladium, and rhodium deposition to the Prunus laurus cerasus leaf surface as an indicator of the vehicular traffic pollution in the city of Varese area: an easy and reliable method to detect PGEs released from automobile catalytic converters

Isotope dilution inductively coupled plasma time-of-flight mass spectrometry (ID-ICP-TOFMS) with desolvating sample introduction and He collision gas for high-accuracy determination of Rh, Pd and Pt in automobile catalytic converters

Quantitative detection of trace elemental palladium in automobile exhaust catalysts through electron probe microanalysis

Determination of Platinum, Palladium and Rhodium in Biological and Environmental Samples by Low Temperature Electrothermal Vaporization Inductively Coupled Plasma Atomic Emission Spectrometry with Diethyldithiocarbamate As Chemical Modifier

Recovery of Platinum Group Metals from Spent Automotive Catalyst

A Method for Determination of PGE–Re Concentrations and Os Isotopic Compositions in Environmental Materials