Abstract:Three dimensional (3D) printing technology has been widely evaluated for the fabrication of various anthropomorphic phantoms during the last couple of decades. The demand for such high quality phantoms is constantly rising and gaining an ever-increasing interest. Although, in a short time 3D printing technology provided phantoms with more realistic features when compared to the previous conventional methods, there are still several aspects to be explored. One of these aspects is the further development of the current 3D printing methods and software devoted to radiological applications. The current 3D printing software and methods usually employ 3D models, while the direct association of medical images with the 3D printing process is needed in order to provide results of higher accuracy and closer to the actual tissues' texture. Another aspect of high importance is the development of suitable printing materials. Ideally, those materials should be able to emulate the entire range of soft and bone tissues, while still matching the human's anatomy. Five types of 3D printing methods have been mainly investigated so far: (a) solidification of photo-curing materials; (b) deposition of melted plastic materials; (c) printing paper-based phantoms with radiopaque ink; (d) melting or binding plastic powder; and (e) bio-printing. From the first and second category, polymer jetting technology and fused filament fabrication (FFF), also known as fused deposition modelling (FDM), are the most promising technologies for the fulfilment of the requirements of realistic and radiologically equivalent anthropomorphic phantoms. Another interesting approach is the fabrication of radiopaque paper-based phantoms using inkjet printers. Although, this may provide phantoms of high accuracy, the utilized materials during the fabrication process are restricted to inks doped with various contrast materials. A similar condition applies to the polymer jetting technology, which despite being quite fast and very accurate, the utilized materials are restricted to those capable of polymerization. The situation is better for FFF/FDM 3D printers, since various compositions of plastic filaments with external substances can be produced conveniently. Although, the speed and accuracy of this 3D printing method are lower compared to the others, the relatively low-cost, constantly improving resolution, sufficient printing volume and plethora of materials are quite promising for the creation of human size heterogeneous phantoms and their adaptation to the treatment procedures of patients in the current health systems.

Geometrically complex 3D-printed phantoms for diffuse optical imaging

A Multiparameter Tissue-Mimicking Phantom for Multispectral Endoscopic Imaging

Fabrication of Tuneable Tissue-Mimicking Phantom for Optical Methods

3D Printing of Tissue-Simulating Phantoms for Calibration of Biomedical Optical Devices

Phantom Preparation and Optical Property Determination

3D Printing Materials Mimicking Human Tissues after Uptake of Iodinated Contrast Agents for Anthropomorphic Radiology Phantoms

Fabrication and characterization of multi-biomarker optimized tissue-mimicking phantoms for multi-modal optical spectroscopy

Multimodal 3D Printing of Phantoms to Simulate Biological Tissue.

Technical Note: Development of a 3D printed subresolution sandwich phantom for validation of brain SPECT analysis

3D printing methods for radiological anthropomorphic phantoms

3D printing surgical phantoms and their role in the visualization of medical procedures

Three-dimensional fuse deposition modeling of tissue-simulating phantom for biomedical optical imaging

Realistic 3D printed imaging tumor phantoms for validation of image processing algorithms

3D-printed Shepp-Logan phantom as a real-world benchmark for MRI

Design of a head phantom produced on a 3D rapid prototyping printer and comparison with a RANDO and 3M lucite head phantom in eye dosimetry applications

PixelPrint: Generating Patient-Specific Phantoms for Spectral CT using Dual Filament 3D Printing

Low-cost tissue simulating phantoms with adjustable wavelength-dependent scattering properties in the visible and infrared ranges

High-fidelity anatomical phantoms for MRI practical training

Design, construction, and dosimetry of 3D printed heterogeneous phantoms for synchrotron brain cancer radiation therapy quality assurance

Novel pore size‐controlled, susceptibility matched, 3D‐printed MRI phantoms

Radioactive 3D printing for the production of molecular imaging phantoms