Abstract:PURPOSE: Human cortical bone has a rapid T2∗ decay, and it can be visualized using ultrashort echo time (UTE) techniques in magnetic resonance imaging (MRI). These sequences operate at the limits of gradient and transmit-receive signal performance. Development of multicompartment anthropomorphic phantoms that can mimic human cortical bone can assist with quality assurance and optimization of UTE sequences. The aims of this study were to (a) characterize the MRI signal properties of a photopolymer resin that can be 3D printed, (b) develop multicompartment phantoms based on the resin, and (c) demonstrate the feasibility of using these phantoms to mimic human anatomy in the assessment of UTE sequences.METHODS: A photopolymer resin (Prismlab China Ltd, Shanghai, China) was imaged on a 3 Tesla MRI system (Siemens Skyra) to characterize its MRI properties with emphasis on T2∗ signal and longevity. Two anthropomorphic phantoms, using the 3D printed resin to simulate skeletal anatomy, were developed and imaged using UTE sequences. A skull phantom was developed and used to assess the feasibility of using the resin to develop a complex model with realistic morphological human characteristics. A tibia model was also developed to assess the suitability of the resin at mimicking a simple multicompartment anatomical model and imaged using a three-dimensional UTE sequence (PETRA). Image quality measurements of signal-to-noise ratio (SNR) and contrast factor were calculated and these were compared to in vivo values.RESULTS: The T2∗ and T<sub>1</sub> (mean ± standard deviation) of the photopolymer resin was found to be 411 ± 19 μs and 74.39 ± 13.88 ms, respectively, and demonstrated no statistically significant change during 4 months of monitoring. The resin had a similar T2∗ decay to human cortical bone; however, had lower T<sub>1</sub> properties. The bone water concentration of the resin was 59% relative to an external water reference phantom, and this was higher than in vivo values reported for human cortical bone. The multicompartment anthropomorphic head phantom was successfully produced and able to simulate realistic air cavities, bony anatomy, and soft tissue. Image quality assessment in the tibia phantom using the PETRA sequence showed the suitability of the resin to mimic human anatomy with high SNR and contrast making it suitable for tissue segmentation.CONCLUSIONS: A solid resin material, which can be 3D printed, has been found to have similar magnetic resonance signal properties to human cortical bone. Phantoms replicating skeletal anatomy were successfully produced using this resin and demonstrated their use for image quality and segmentation assessment of ultrashort echo time sequences.

3D-printed Shepp-Logan phantom as a real-world benchmark for MRI

3D printed phantoms mimicking cortical bone for the assessment of ultrashort echo time magnetic resonance imaging

A reusable 3D printed brain‐like phantom for benchmarking electrical properties tomography reconstructions

Nanoporous hollow fibers as a phantom material for the validation of diffusion magnetic resonance imaging

Technical Note: Development of a 3D printed subresolution sandwich phantom for validation of brain SPECT analysis

High-fidelity anatomical phantoms for MRI practical training

Novel pore size‐controlled, susceptibility matched, 3D‐printed MRI phantoms

A multi-modality medical imaging head and neck phantom: Part 2. Medical imaging

A Digital Phantom for 3D MR Spectroscopy Data Simulation

An anthropomorphic multimodality (CT/MRI) phantom prototype for end-to-end tests in radiation therapy

Phantom for quantitatively measuring MRI artifact

Geometrically complex 3D-printed phantoms for diffuse optical imaging

Fabrication and characterization of multi-biomarker optimized tissue-mimicking phantoms for multi-modal optical spectroscopy

A novel 3D-printed head phantom with anatomically realistic geometry and continuously varying skull resistivity distribution for electrical impedance tomography

Quantitative magnetic resonance imaging phantoms: A review and the need for a system phantom

Stable Tissue-Mimicking Phantoms for Longitudinal Multimodality Imaging Studies That Incorporate Optical, CT, and MRI Contrast

Development of a CT-Compatible, Anthropomorphic Skull and Brain Phantom for Neurosurgical Planning, Training, and Simulation

Realistic 3D Phantoms for Validation of Microwave Sensing in Health Monitoring Applications

PixelPrint: Generating Patient-Specific Phantoms for Spectral CT using Dual Filament 3D Printing

Creation of an anthropomorphic CT head phantom for verification of image segmentation

Fabrication of Customizable Intraplaque Hemorrhage Phantoms for Magnetic Resonance Imaging