Abstract:Background Medical examinations or treatment of pregnant women using ionizing radiation are sometimes unavoidable. In such cases, the risk of harm to the embryo and fetus after exposure to ionizing radiation must be carefully estimated. However, no commercially available anthropomorphic body phantoms of pregnant women are available for dose measurements. A promising possibility for the production of body phantoms for patient groups that are not adequately represented by the phantoms of reference persons is 3D printing. However, this approach is still in the evaluation phase. Purpose To print the abdomen of a woman in the late stage of pregnancy and compare the dose distribution measured using thermoluminescence dosimeters (TLDs) in the printed phantom for two different computed tomography (CT) protocols with the corresponding results of Monte Carlo simulations on voxel models of the pregnant woman. Materials and methods The physical phantom was produced through multi‐material extrusion printing using different print materials identified in previous studies to simulate homogeneous soft tissues and the mean compositions of maternal and fetal bones. The 3D printed abdomen was combined with a conventionally produced anthropomorphic female phantom to obtain a whole‐body phantom of a pregnant woman. Dose values resulting from two different CT scans acquired at tube voltages of 80 and 120 kV were measured using TLDs positioned in the physical phantom and cross‐validated with the results of Monte Carlo simulations performed for two different voxel models. The first was a voxelized model of the produced phantom itself and the second a realistic digital model of a pregnant woman. Representative CT values of the materials used in the printed phantom were determined from the acquired CT images. Results The CT values of maternal and fetal tissue structures in the phantom are comparable to CT values of real human tissues. The difference between most organ doses measured in the 3D printed phantom and simulated in the voxel models was below 20% and equivalent within the measurement uncertainties. Only the dose to the fetal head was up to 50% higher and not equivalent for the realistic model and the 80 kV‐protocol. As expected, the agreement was better for the voxelized than for the realistic model. For both models a slight energy dependence was observed, with larger deviations for the 80‐kV protocol especially for organs located in the pelvic region. Conclusion Individualized physical body phantoms, such as that of a pregnant woman, can be produced using 3D printing. The good agreement between measured and simulated doses to the fetus cross‐validates both dosimetric methods. Therefore, this study demonstrates the suitability of 3D printing phantoms for patients not adequately represented by commercially available body phantoms of reference persons.

Development of fetal magnetic resonance imaging (MRI) phantom

High-fidelity anatomical phantoms for MRI practical training

Maturation-informed synthetic Magnetic Resonance Images of the Developing Human Fetal Brain

3D printing of realistic body phantoms: Comparison of measured and simulated organ doses on the example of a CT scan on a pregnant woman

Hybrid computational pregnant female phantom construction for radiation dosimetry applications

3D printed phantoms mimicking cortical bone for the assessment of ultrashort echo time magnetic resonance imaging

A multi-modality medical imaging head and neck phantom: Part 2. Medical imaging

Development and evaluation of a novel MR-compatible pelvic end-to-end phantom

Narrative review of tissue-mimicking materials for MRI phantoms: Composition, fabrication, and relaxation properties

3D-printed Shepp-Logan phantom as a real-world benchmark for MRI

A patient-specific multi-modality abdominal aortic aneurysm imaging phantom

Stable Tissue-Mimicking Phantoms for Longitudinal Multimodality Imaging Studies That Incorporate Optical, CT, and MRI Contrast

3D Printing Materials Mimicking Human Tissues after Uptake of Iodinated Contrast Agents for Anthropomorphic Radiology Phantoms

A Dynamic Ultrasound Phantom with Tissue‐Mimicking Mechanical and Acoustic Properties

MRI-compatible abdomen phantom to mimic respiratory-triggered organ movement while performing needle-based interventions

An anthropomorphic multimodality (CT/MRI) phantom prototype for end-to-end tests in radiation therapy

Development of a Computerized 4-D MRI Phantom for Liver Motion Study

ICRP pregnant-female mesh-type reference computational phantoms part 1: development of fetal phantoms

A generalized system of tissue-mimicking materials for computed tomography and magnetic resonance imaging

Development of an anatomical breast phantom from polyvinyl chloride plastisol with lesions of various shape, elasticity and echogenicity for teaching ultrasound examination

Applicability of three-dimensional imaging techniques in fetal medicine