Impact of a ping-pong ball

Rod Cross

DOI: https://doi.org/10.1088/1361-6552/aa5f84

2017-03-20

Physics Education

Abstract:Measurements are presented of the impact time, peak force and centre of mass displacement of a ping-pong ball impacting vertically on a hard, horizontal surface. The results are compared with a recent measurement described in this journal.

What problem does this paper attempt to address?

Collision and Rebound of Ping Pong Balls on A Rigid Target

R. H. Bao,T. X. Yu

DOI: https://doi.org/10.1016/j.matdes.2015.08.019

IF: 9.417

2015-01-01

Materials & Design

Abstract:The collision and rebound behavior of ping pang balls impinging onto rigid target are studied. Three dimensionless dominant parameters are identified: (1) the ratio of the wall-thickness to the average radius of the ball; (2) the dimensionless initial velocity; and (3) the yield strain of the material.Depending on the dimensionless initial velocity, various collision and rebound behaviors of the ball are revealed: (1) When the initial velocity is low, the deformation of the ball remains purely elastic, for which the characteristic duration is theoretically obtained; (2) With the increase of initial velocity, the ball's cap begins to buckle and multiple impacts occur, leading to the increase of the restitution duration and the reduction of the coefficient of restitution (COR); (3) With the higher initial velocity, the ball's cap buckles permanently, leading to the disappearance of multiple impacts and a sudden drop of the restitution duration; consequently the COR decreases from 0.5 to 03; and (4) When the initial velocity is close to the material's yield velocity, the ball buckles into a non-axisymmetric mode.The simulation results are also compared with experimental ones. Furthermore, the effects of thickness-to-radius ratio, yield strain and coefficient of friction are also discussed. (C) 2015 Elsevier Ltd. All rights reserved.
Rebound Modeling of Spinning Ping-Pong Ball Based on Multiple Visual Measurements

Yongsheng Zhao,Rong Xiong,Yifeng Zhang

DOI: https://doi.org/10.1109/tim.2016.2555179

IF: 5.6

2016-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:The research on the collision between a spinning ball and a table, as a general issue for the trajectory analysis of the spinning-flying objects, is important but complicated. Traditionally, it is studied either by simplifying the collision process as a black box in which the ball's motion state changes abruptly before and after collision, or by assuming that the coefficient of restitution and the coefficient of friction are simply piecewise linear or even constant during the whole collision process. In this paper, we first analyze the mechanism of the collision dynamics and conclude from mathematical derivations that the collision between a ping-pong ball and a table is a continuous transition process and its collision duration is a constant irrelevant to the ball's motion state. These two conclusions are also verified by the visual measurement using an ultrahigh-speed camera. Then, we propose a novel rebound model using the mean value theorem, momentum theorem, and angular momentum theorem. The novelty of the proposed model is that the forces and the parameters in it are formulated as the continuous functions related to the ball's motion state, which is more accurate, rather than as constants. The integrations of these functions over time can be formulated by using the mean value theorem, and their expressions are learned using multilayer perception with a large data set collected by the position vision system and the pan-tilt vision system. The experimental results verify the effectiveness and accuracy of the proposed model.
Experimental and Numerical Study on the Dynamic Buckling of Ping-pong Balls under Impact Loading

X. W. Zhang,T. X. Yu

DOI: https://doi.org/10.1515/ijnsns-2011-0103

2012-01-01

International Journal of Nonlinear Sciences and Numerical Simulation

Abstract:Abstract By means of ping-pong balls, the dynamic buckling behaviours of thin-walled spherical shells under impact loading are studied both experimentally and numerically. First, the quasi-static tests were conducted on an MTS tester, in which the ball was compressed onto a PMMA plate. Apart from the force-displacement relationship, the evolution of the contact zone between the ball and the plate was obtained by a digital camera. In the impact tests, ping-pong balls were accelerated by an air-gun and then impinged onto a rigid plate with the velocity ranging 10–45 m

mechanics,engineering, multidisciplinary,mathematics, applied,physics, mathematical
Impact–contact Dynamics in a Disc–ball System

Caishan Liu,Hongjian Zhang,Zhen Zhao,Bernard Brogliato

DOI: https://doi.org/10.1098/rspa.2012.0741

2013-01-01

Abstract:This paper concerns a disc–ball system, in which a moving ball collides against a disc resting on a rough, fixed horizontal surface. The complexity in such a simple object is due to the presence of the line contact between the disc and the fixed plate, which significantly influences the impact-generated state of the disc. We deal with this problem in a uniform framework that encapsulates different structures of the mathematical model, including contacts, impacts, stick–slip in friction, as well as the transitions among different states of the variable-structure dynamics. We design specific experiments that provide useful information to help determine the macroscopic parameters in impact and friction. Other complicated cases concerned with the couplings between impacts and friction are theoretically and experimentally investigated. Excellent agreements between numerical and experimental results support our theoretical developments.
Millisecond measurements without equipment: time of collision of a ping-pong ball with a table

Ivan V Oladyshkin,Anastasia A Oladyshkina

DOI: https://doi.org/10.1088/1361-6552/52/1/013006

2016-12-08

Physics Education

Abstract:We describe a simple experiment giving the opportunity to estimate the time of collision of a freely falling ping-pong ball and a table. The method is based on the ball deformation measurement and uses just elementary geometry and kinematics.
EXPERIMENTAL STUDY OF IMPACT FORCE OF A LOW-SPEED DROPLET COLLIDING ON THE SOLID SURFACE AT DIFFERENT IMPACT ANGLES

Bin Zhang,Qian Lv,Penghua Guo,Jingyin Li

DOI: https://doi.org/10.1115/imece2017-70882

2018-01-01

Abstract:Erosion problems due to droplet impacts are widely encountered in many fields. This may result in deterioration or even failure of the elements, and should be taken into consideration in the design of machines. The impact force is thought of as an essential factor in material erosion. In this paper, a highly sensitive piezoelectric force transducer was employed to record the impact force of the low-speed droplet colliding on an aluminum plate at different impact angles, in combination with a high-speed camera used to capture the impact process of the droplet. The results showed that the experimental setup can measure the impact force evolution precisely and reliably. The peak of the normal impact force increases with the normal velocity quadratically, while the impulse increases with the normal velocity linearly. In addition, a smaller impact angle would lead to longer time duration of the impact force. The high-speed images show that the initial impact patterns of the droplet have similar behavior in the initial impact process, with regardless of vertical or oblique impacts.
Experimental analysis of impacts with large elastic deformation: I. Linear motion

Alan Hocknell,Roy Jones,Steve Rothberg

DOI: https://doi.org/10.1088/0957-0233/7/9/009

IF: 2.398

1996-09-01

Measurement Science and Technology

Abstract:A measurement system is presented which uses a small number of sensors to capture relevant information by a limited number of measurements during a high-speed impact between two lightweight bodies. Two laser Doppler vibrometers and a piezoelectric accelerometer are arranged to capture data from which the variation of deformations, velocities and forces over time during an impact can be determined. The golf club - ball impact is chosen as an example. Large elastic deformations are measured on the golf ball during the impact and these can be related to the variation of the impact force over time. This information leads to greater understanding of the relationship between two impacting bodies and can be used in the validation of analysis by techniques such as finite element modelling.

engineering, multidisciplinary,instruments & instrumentation
Normal impact of a ball rotating around its linear velocity

Théophile Rémond,Vincent Dolique,Renaud G Rinaldi,Jean-Christophe Géminard

DOI: https://doi.org/10.1103/PhysRevE.110.015002

Abstract:We report on an experimental study of the normal impact on a solid surface of a table tennis ball that rotates around its linear velocity vector. We observe that the ratio of the reflected velocity to the incident velocity does not depend on the initial spin. In contrast, the reflected spin depends not only on the incident spin but also on the incident velocity. The experimental results, which reveal the tricky role played by the friction in the region of contact, are accounted for by simple theoretical arguments.
Real-Time Measurement of Ping-Pong Ball Velocity Based on Image Processing

T Hu,J Yang,ZB Pu

DOI: https://doi.org/10.1117/12.483249

2002-01-01

Abstract:In this paper, we described a real-time measurement technique for analyzing flying ping-pong ball movement. A high picking rate CCD camera was selected, and the ping-pong ball was marked with two different colors. A fast algorithm which applied dynamic windows to determine the position of object was introduced. Through position-finding of mass center, measurement of the highest linear speed 40m/s can be obtained. Technique of FFT processes video images of marks on a ping-pang ball to get rotational speed. The highest rotatory speed of this measurement can reaches 200 r/s. The preliminary experimental results were obtained and its performance coincided with the theory. Relative error of this system was better than 5%.
Impact and Rebound of an Elastic–plastic Ring on a Rigid Target

R. H. Bao,T. X. Yu

DOI: https://doi.org/10.1016/j.ijmecsci.2014.03.031

IF: 7.3

2015-01-01

International Journal of Mechanical Sciences

Abstract:This paper studies the impact and rebound behaviour of a thin-walled elastic-plastic circular ring after it impinges onto a rigid wall with initial velocity V-0 by finite element method. Through the dimensional analysis and a systematic simulation with different ring geometries and material properties, three non-dimensional parameters are identified, which dominate the impact duration and rebound velocity of the ring; and they are: (1) the ratio of wall thickness to average radius, eta=h/R; (2) the yield strain of the material, Y/E; and (3) the non-dimensional initial velocity of the ring, nu = V-0/V-Y, where V-Y = Y/(E rho)(1/2) denotes the yield velocity of the material [3].When the initial velocity is low, the impact between the ring and rigid plate remains elastic, the compression duration could be analytically obtained, and it agrees well with the numerical results, while the restitution duration is about 3/4 of the compression duration. The corresponding coefficient of restitution (COR) is found to be independent from the material property, whereas it increases from 0.75 to 0.78 when the thickness ratio changes from 1/20 to 1/40. With the increasing of initial velocity, a four-hinge crushing mode and a subsequent five-hinge mode are identified, which are different from the crushing mode of a ring under static compression. The variations of compression and restitution durations, rebound velocity and COR are discussed in detail, while some of them are compared with those of the impact of a solid ball onto a rigid wall. The effects of the ring geometry and material properties on these variables are also presented. The rebound velocity is found to reach the maximal at about a half of material's yield velocity when the initial velocity of the ring is about twice of the yield velocity, resulting in COR being 0.25 for all the materials and geometries adopted in this paper. (C) 2014 Elsevier Ltd. All rights reserved.
Impact Crushing and Rebound of Thin-Walled Hollow Spheres

Ronghao Bao,T. X. Yu

DOI: https://doi.org/10.4028/www.scientific.net/kem.535-536.40

2013-01-01

Key Engineering Materials

Abstract:The dynamic behavior of a thin-walled hollow sphere colliding onto a rigid wall has been studied by experiments, numerical simulation and analytical modeling, as reported in our previous papers. In the present paper, the impact crushing of metallic thin-walled hollow spheres onto rigid plates and the subsequent rebound are analyzed using finite element method. The effects of hollow sphere's thickness-to-radius ratio, the material properties and the impact velocity on the dynamic responses are systematically investigated. The transition from axisymmetric dimpling to non-axisymmetric lobing is found to depend on the relative thickness of spheres and impact velocity; while the coefficient of restitution almost merely depends on impact velocity.
Effects of Droplet Shape on Impact Force of Low-Speed Droplets Colliding with Solid Surface

Ruizi Zhang,Bin Zhang,Qian Lv,Jingyin Li,Penghua Guo

DOI: https://doi.org/10.1007/s00348-019-2712-7

IF: 2.797

2019-01-01

Experiments in Fluids

Abstract:The impact forces of the low-speed water droplet colliding on a light and tiny aluminum plate were measured by using a highly sensitive piezoelectric force transducer. The one-degree freedom vibration model was employed to analyze the oscillation of the measured force signals, and the plate vibration was confirmed as the cause through elaborately designed experiments. The force data were obtained by using the low-pass Finite Impulse Response filter and was verified to be reliable. The effects of impact velocity and diameter of droplets on the impact force evolutions and peak forces were investigated. The results revealed that the impact process of a liquid droplet is quite different from that of a solid ball in the frequency spectrum and in the power function of the peak force. The droplet impact is closer to a plastic impact, while the other behaves more nearly an elastic impact. The influence of droplet size on erosion is dependent on the impact time duration, which increases with droplet diameter. On the other hand, the impact pressure is the main cause of the material erosion when impact velocity is taken as the influence factor.
Quantized Impact of Rod on Plate

Qing Peng,Xiaoming Liu,Yue-Guang Wei

DOI: https://doi.org/10.1016/j.jmps.2024.105680

IF: 5.582

2024-05-07

Journal of the Mechanics and Physics of Solids

Abstract:In this work, we attacked the problem of elastic impact of a rod on a plate. By considering wave propagation on the plate and along the rod, we established a mathematic model with delay differential equation that governs such impact. The proposed model could consolidate classical impact problems from bead-on-wall, bead-on-plate, to rod-on-wall impact. Solving the governing equation, we obtained a universal loading and unloading history of such impact: the unloading history exhibits quantized plateaus, the values of which are quantitatively provided in the present study. Also, the contact duration also shows a band structure while tuning the compliance of plate. In addition, we analyzed the overshoots leading the plateaus during unloading, which cause the final detachment between the rod and the plate.

mechanics,materials science, multidisciplinary,physics, condensed matter
Analysis of Drop Point Track of Ping Pong Ball After Hitting Based on Dynamic Analysis

B Wang

DOI: https://doi.org/10.21152/1750-9548.14.2.193

2020-06-30

The International Journal of Multiphysics

Abstract:Table tennis is a popular sport in China. It has a low barrier to entry and also has difficult techniques. In order to improve the skills of table tennis match between players, this paper introduced the dynamic analysis of ping pong ball in flight after being hit. The main content was the stress analysis in the flight of ping pong ball. Moreover, the Magnus force caused by rotation was considered. The dynamic model of ping pong ball flight was built, the flight track of top spinning ball at 0, 30, 60, 90 and 120 r/s was simulated using Java software. The actual flight track of ping pong ball under the same conditions was obtained using the table tennis serving machine and high-speed camera to verify the effectiveness of the dynamic model. The results showed that the track obtained by the dynamic model basically coincided with the actual track, which verified the validity of the dynamic model; the maximum height and drop point distance of ping pong ball decreased with the increase of spinning speed of top spinning ball; the flight time of ping pong ball decreased with the increase of spinning speed of top spinning ball. To sum up, players can reduce the flight height, drop point distance and flight time of ping pong ball by increasing the top spinning speed, so as to improve the opponent's counterattack difficulty.
Energy Evolution in Complex Impacts with Friction

HongJian Zhang,CaiShan Liu,Zhen Zhao,Bernard Brogliato

DOI: https://doi.org/10.1007/s11433-013-5061-1

2013-01-01

Abstract:In this paper, we base a theory established in an impulse-energy level to solve a problem of a disk-ball system, in which a moving ball collides perpendicularly against an disk staying on a horizontal surface. The impact process is an ensemble consisting of a point impact coupled with a line contact between bodies of the disk, the ball and the fixed horizontal surface. We experimentally and theoretically show that the post-impact states of the disk dramatically vary with the impacting position of the ball. Explanations are given by investigating the evolutions of the potential energies resided in the points involved in the complex frictional impacts. Good agreements between numerical and experimental results strongly suggest that the evolution of energy together with the dissipation must be reflected in mathematical models if a precise description for the post-impact state of systems is expected.
Dissipative properties for a ball bouncing on a vertically vibrating plate

Z.H. Jiang,Z.J. Liang,D.W. Zhou,Y.J. Deng

DOI: https://doi.org/10.1016/j.physa.2019.123875

2020-01-01

Abstract:The collision characteristics of a ball impacting on a vertically vibrating plate are different from those normally presented in the ball-ball or ball-plate collision, because the vibration of the plate inevitably gets involved in the collision process. We experimentally study the behavior of a steel ball bouncing on a vertically vibrating plate, and determine the dependence of the coefficient of restitution and the collision duration on the impact velocity. In the experiment, a double-layer composite structural plate is used, which is formed by gluing a piece of polyethylene onto a stainless steel sheet. It is found that the vibration of the plate makes the coefficient of restitution to be no longer a single-valued function of the impact velocity, but rather multi-valued, and exhibit a complex but regular dispersion structure. To account for such dispersion structure, a collision dynamics model is developed in which the inertial force due to the vibration of the plate is included. The energy loss caused by viscous deformation and inertial force is analyzed. Both the coefficient of restitution and the collision duration calculated by this model agree well with the experimental ones.
Effect Of Plastic Table Tennis On The Coefficient Of Friction Between Racket And Ball

Dandan Xiao,Jing Ren,Li Qin,Xinqing Ma,Wanting Zhang

2017-01-01

Abstract:The coefficient of friction between racket and ball was tested by UMT-2 multi-functional micro tribometer, and the roughness of any three of the five points on the two kinds of table tennis balls were measured by white-light interfering profilomete in the State Key Laboratory at Tsinghua University, aimed to study the effect of plastic table tennis on the coefficient of friction between racket and ball. The results showed that: (1) the application of plastic table tennis ball decreased force of friction and the coefficient of friction between pimples in and ball, thus the rotation of ball reduced by 3.25%; (2) the roughness and the evenness of plastic table tennis ball is less than that of Celluloid table tennis ball.
Effect of table tennis balls with different materials and structures on the hardness and elasticity

Yunfei Lu,Jie Ren,Jun Wang,Yan Wang

DOI: https://doi.org/10.1371/journal.pone.0301560

IF: 3.7

2024-04-18

PLoS ONE

Abstract:The new material introduced by the ITTF in 2014 for table tennis balls has attracted significant attention from players and coaches. Changes in both material selection and production procedures are likely to have affected the static performance of the ball. However, the raw data regarding the elasticity and hardness of these new material balls, encompassing various brands and structures, often lacks practical information crucial for players’ rapid adaptation and daily training. The static properties tested in this study were provided by the ITTF, covering both hardness and elasticity. Based on computed variables, this study revealed that the hardness of seam balls at the equator was not consistently higher than that at the pole. Additionally, the study confirmed that the hardness and bounce height of new material balls exceeded those of celluloid. Furthermore, correlation analysis was conducted to examine the relationship between these two properties, revealing a significant correlation between the hardness of seamless balls and their elasticity. This study provides an analysis of the static performance of various types of new material balls, aiding players and coaches in better understanding official event balls and offering a theoretical foundation for the formulation of diverse training and game strategies.

multidisciplinary sciences
Inelastic bouncing of a spherical ball in the presence of quadratic drag with application to sports balls

Marko V. Lubarda,Vlado A. Lubarda

DOI: https://doi.org/10.1177/17543371221086190

2022-04-05

Abstract:The bouncing motion of a spherical ball following its repeated inelastic impacts with a horizontal flat surface is analyzed. The effect of air resistance on the motion of the ball is accounted for by using the quadratic drag model. The effects of inelastic impacts are accounted for by using the coefficient of restitution, which is assumed to remain constant during repeated impacts. Also presented is an extension of the analysis allowing for a velocity-dependent coefficient of restitution. Closed-form expressions are derived for the velocity, position, maximum height, duration, and dissipated energy during each cycle of motion. The decrease of successive rebound heights in the presence of air resistance is more rapid for higher values of the launch velocity, because the drag force is stronger and acts longer. Air resistance can significantly affect the value of the coefficient of restitution determined in a dropping ball test. For a given number of rebounds, the energy dissipated by inelastic impacts is greater than the energy dissipated by air resistance, if the launch velocity is sufficiently small. The opposite is true for greater values of the launch velocity. The derived formulas are applied to analyze the bouncing motion of a ping pong ball, tennis ball, handball, and a basketball.
Performance Effects of Different Table Tennis Ball Materials

Yu-Fen Chen,Chen-Chih Huang

DOI: https://doi.org/10.1080/23080477.2020.1786230

2020-04-02

Smart Science

Abstract:The performance of two different table tennis balls (i.e. a seamless poly ball and a seamed celluloid ball) is compared both experimentally and numerically. No significant difference is found in the coefficients of restitution of the two balls in free-fall impact tests onto a flat rubber surface. However, the celluloid ball has a faster rotational speed on serving, while the poly ball has a greater rebound angle. However, on serving, the celluloid ball has a faster spinning speed than the poly ball, while the poly ball has a greater rebound angle. In addition, for a given spin rotation speed and serving speed, the celluloid ball has a faster sink velocity than the seamless poly ball.To evaluate the spinning speeds of the two balls, an observation mark was made on the surface of each ball and the ball was then fired by a serving machine at a pre-determined initial speed. The figures describe the rebound angle measured methods.

Impact of a ping-pong ball

Collision and Rebound of Ping Pong Balls on A Rigid Target

Rebound Modeling of Spinning Ping-Pong Ball Based on Multiple Visual Measurements

Experimental and Numerical Study on the Dynamic Buckling of Ping-pong Balls under Impact Loading

Impact–contact Dynamics in a Disc–ball System

Millisecond measurements without equipment: time of collision of a ping-pong ball with a table

EXPERIMENTAL STUDY OF IMPACT FORCE OF A LOW-SPEED DROPLET COLLIDING ON THE SOLID SURFACE AT DIFFERENT IMPACT ANGLES

Experimental analysis of impacts with large elastic deformation: I. Linear motion

Normal impact of a ball rotating around its linear velocity

Real-Time Measurement of Ping-Pong Ball Velocity Based on Image Processing

Impact and Rebound of an Elastic–plastic Ring on a Rigid Target

Impact Crushing and Rebound of Thin-Walled Hollow Spheres

Effects of Droplet Shape on Impact Force of Low-Speed Droplets Colliding with Solid Surface

Quantized Impact of Rod on Plate

Analysis of Drop Point Track of Ping Pong Ball After Hitting Based on Dynamic Analysis

Energy Evolution in Complex Impacts with Friction

Dissipative properties for a ball bouncing on a vertically vibrating plate

Effect Of Plastic Table Tennis On The Coefficient Of Friction Between Racket And Ball

Effect of table tennis balls with different materials and structures on the hardness and elasticity

Inelastic bouncing of a spherical ball in the presence of quadratic drag with application to sports balls

Performance Effects of Different Table Tennis Ball Materials