Abstract:The fabrication of high-end ceramics by additive manufacturing gained increasing research interest due to the capacity of these techniques to break through the limitations of traditional extractive manufacturing. Although efficient strategies for the processing of ceramic materials by additive manufacturing have been shown, with notable examples in the dental field, the processing of dense glass-ceramics by the same means is almost unexplored. Herein, a processing strategy for the manufacture of complex shapes of lithium disilicate glass-ceramics by material extrusion is detailed shown for the first time. An aging behaviour was observed on the glass loaded aqueous suspensions and in-deep studied, being related with the leaching of Li + ions. Based on this, a hydrogel-based ink with high solid content (φ≈ 50 vol%), suitable rheological properties (G ́≈10 6 and τ ≈1500 Pa) and recovery time was developed. By using the optimized ink, a propeller component with high aspect ratio and small internal connected channels, as well as a dental crown were successfully printed. A debinding schedule was tuned by the combination of differential thermal analysis and hot stage microscopy. The sintered lithium disilicate glass-ceramic parts presented good relative density (≈ 96.7 ± 0.8%) and translucency. Outstanding mechanical properties were achieved (Hv ≈5.3 GPa, K If ≈2.1 MPa.m 0.5 , σ ≈279 ± 44 MPa), comparable to values usually attained for these materials by powder technology. The low deviation of the flexural strength data reported here is related with the absence of meaningful processing defects on the analysed fracture surfaces and the homogeneous distribution of the residual porosity as microporous, resulting in a good Weibull characteristic strength σ 0 = 301 MPa. The results of the present work emphasized the potential of Direct ink Writing, a material extrusion technique, to fabricate lithium disilicate glass-ceramic parts with complex geometries, as dental crowns.

The study of near-net shape lithium aluminosilicate glass-ceramics by direct ink writing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Complex shapes of lithium disilicate glass-ceramics developed by material extrusion

Formation mechanism and controlling strategy of lamellar structure in 3D printed alumina ceramics by digital light processing

Mechanical properties and wear behaviors analysis of fluorapatite glass-ceramics based on stereolithography 3D printing

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Mechanical and Dielectric Properties of 3D Printed Highly Porous Ceramics Fabricated Via Stable and Durable Gel Ink

Microstructure and properties evolution of silicon-based ceramic cores fabricated by 3D printing with stair-stepping effect control

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

3D printing of unsupported multi-scale and large-span ceramic via near-infrared assisted direct ink writing

Reinforcement effect in printing precision and sintering performance for liquid crystal display stereolithography additive manufacturing of alumina ceramics

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Direct ink writing of aluminum-phosphate-bonded Al2O3 ceramic with ultra-low dimensional shrinkage

Effects of raw material ratio and post-treatment on properties of soda lime glass-ceramics fabricated by selective laser sintering

3D printing of ceramics with controllable green‐body configuration assisted by the polyvinyl alcohol‐based physical gels

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Fabrication of fine and complex lattice structure Al2O3 ceramic by digital light processing 3D printing technology

Three-Dimensional Printing of Yttrium Oxide Transparent Ceramics via Direct Ink Writing

Microstructures and mechanical properties of additively manufactured alumina ceramics with digital light processing

Fused silica ceramic core based on network-structured zircon design via 3D printing