Abstract:Laser powder bed fusion (LPBF) allows the fabrication of complex parts with high resolution. In the process of manufacturing complex parts, overhanging structures with unique mechanical properties are inevitable. The mechanical properties are relevant to the microstructure that are severely influenced by the support structures and build orientation. In this study, a three-dimensional finite element model was established to numerically investigate the thermal behavior of the melt pool in the overhanging structures, and the effects of different forming conditions on tensile behavior were analyzed through the microstructure of overhanging specimens and fracture surfaces of failed specimens. The simulation results show that the change trend of the melt pool size is the same as that of the maximum temperature. Moreover, the melt pools closer to the down-facing surface of overhanging structures carry higher temperature and larger size. The application of the support structures effectively reduces the temperature of the melt pool in the starting layer by 5.3%. With the increase of inclination angle, the melt pool temperature in the starting layer decreases slightly. The experimental results indicate that the mechanical properties of 45° specimens fabricated above the entity are stronger than those of 45° specimens with support structures, and the mechanical properties of 45° specimens with support structures are stronger than those of 45° specimens without support structures. Moreover, the mechanical properties of the specimens deteriorate when the build orientation of the overhanging structures varies from 0° to 45°. The mechanical properties of different specimens with 45° build orientation are mainly affected by the thickness of defect area, and the mechanical properties of the specimens with different build orientations are mainly affected by fracture path. The results will facilitate the understanding and application of the LPBF manufacturing technique for overhanging structures in complex parts.

The Effects of Overhang Forming Direction on Thermal Behaviors during Additive Manufacturing Ti-6Al-4V Alloy

Experimental investigation on the factors affecting the quality of titanium alloy overhang via selective laser melting forming

Study of the Effect of Selective Laser Melting Process Parameters on Overhang Structures

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Tensile behavior of AlSi10Mg overhanging structures fabricated by laser powder bed fusion: Effects of support structures and build orientation

The influence of building direction on the fatigue crack propagation behavior of Ti6Al4V alloy produced by selective laser melting

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

Role of Scanning Strategy on Residual Stress Distribution in Ti-6Al-4V Alloy Prepared by Selective Laser Melting

Selective Laser Melting of Ti6Al4V: Effects of Heat Accumulation Phenomena due to Building Orientation

Novel Strategy for Reducing Residual Stress in Titanium Alloy Parts Obtained via Additive Manufacturing

Microstructures and Mechanical Behaviors of a Directional Lamellar Ti-48Al-2Cr-2Nb Alloy Produced by Laser Additive Manufacturing

The Thermo-Mechanical Coupling Effect in Selective Laser Melting of Aluminum Alloy Powder

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Grain Selection and Growth Orientation of Prior-Β Phase for Ti-6-4 During Additive Manufacturing: Insights from a Modeling Perspective

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Effects of Post-Processing and Loading Orientation on High-Cycle Fatigue of Selective Laser Melted Ti-6Al-4V

Difference-extent of microstructure and mechanical properties: Simulating multi-laser selective melting Ti6Al4V

A simulation and experiment study on phase transformations of Ti-6Al-4V in wire laser additive manufacturing