Abstract:Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) was developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) were comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibited a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at −20 °C. In contrast, the HR-QT steel exhibited tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consisted of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reached 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared with the HR-QT process, the TMCP-DQP process resulted in a finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieved the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilized the RA through carbon enrichment, while the relaxation stage reduced a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminated internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

A Study on Integrating Deformation Induced Ferrite Transformation with Conventional Thermomechanical Controlled Processing at an Industrial Scale and the Associated Challenges

Innovations in Thermo-mechanical Processing to Develop High Strength Steel Plates

Effect of High-Temperature Severe Plastic Deformation on Microstructure and Mechanical Properties of IF Steel

Effect of Deformation on Microstructure and Mechanical Properties of Medium Carbon Steel During Heat Treatment Process

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

The Microstructure and Mechanical Properties of Ferritic-Martensitic Steel EP-823 after High-Temperature Thermomechanical Treatment

The Impact of Interphase Precipitation on the Mechanical Behavior of Fire-Resistant Steels at an Elevated Temperature

In Situ Observation of Γ → Α Transformation During Hot Deformation in an Fe-Ni Alloy by an X-ray Diffraction Method

An Ultrahigh Strength Steel Produced Through Deformation-Induced Ferrite Transformation and Q&P Process

Effect of Dissolved and Precipitated Niobium in Microalloyed Steel on Deformation Induced Ferrite Transformation (Dift)

Influence of High-Temperature Deformation on the Dissolution of δ-Ferrite in Stainless Steels

Influence of TMCP Parameters on Structure and Properties of Low Carbon Cu Bearing Ultra-High Strength Steel

Microstructural Evolution and High‐Temperature Tensile Properties of 15Cr‐Reduced Activation Ferritic Steel Processed by Hot Powder Forging of Mechanically Alloyed Powders

Precipitation Strengthening of Micro-Alloyed Steels Thermo-Mechanically Processed by Ultra Fast Cooling

Ultrafine Grain Ferrite Transformed from Fine Austenite Grains Produced by Dynamic Reversal Transformation

Consequences of Deep Rolling at Elevated Temperature on Near-Surface and Fatigue Properties of High-Manganese TWIP Steel X40MnCrAl19-2

Studies on Hot Deformation Behavior and Dynamic Recrystallization in a High Al Ferritic Low-Density Steel

Thermo-Mechanical Processing as Method Decreasing Delta-Ferrite and Improving the Impact Toughness of the Novel 12% Cr Steels with Low N and High B Contents

Achieving 2.2 GPa Ultra-High Strength in Low-Alloy Steel Using a Direct Quenching and Partitioning Process

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Effect of Grain Size and Residual Strain on the Dynamic Transformation of Austenite under Plate Rolling Conditions