Abstract:In this work, the structural and mechanical properties of ternary Mo-Al-N alloys are investigated by combining thin film growth experiments and density functional theory (DFT) calculations. Mo1−xAlxNy thin films (∼300 nm thick), with various Al fractions ranging from x = 0 to 0.5 and nitrogen-to-metal (Al + Mo) ratio ranging from y = 0.78 to 1.38, were deposited by direct-current reactive magnetron cosputtering technique from elemental Mo and Al targets under Ar + N2 plasma discharges. The Al content was varied by changing the respective Mo and Al target powers, at a fixed N2 (20 SCCM) and Ar (25 SCCM) flow rate, and using two different substrate temperatures Ts = 350 and 500 °C. The elemental composition, mass density, crystal structure, residual stress state, and intrinsic (growth) stress were examined by wavelength dispersive x-ray spectroscopy, x-ray reflectivity, x-ray diffraction, including pole figure and <math> si n 2 ψ</math> measurements, and real-time in situ wafer curvature. Nanoindentation tests were carried out to determine film hardness H and elastic modulus EIT, while the shear elastic constant C44 was measured selectively by surface Brillouin light spectroscopy. All deposited Mo1−xAlxNy films have a cubic rock-salt crystal structure and exhibit a fiber-texture with a [001] preferred orientation. The incorporation of Al is accompanied by a rise in nitrogen content from 44 to 58 at. %, resulting in a significant increase (2%) in the lattice parameter when x increases from 0 to 0.27. This trend is opposite to what DFT calculations predict for cubic defect-free stoichiometric Mo1−xAlxN compounds and is attributed to variation in point defect concentration (nitrogen and metal vacancies) when Al substitutes for Mo. Increasing Ts from 350 to 500 °C has a minimal effect on the structural properties and phase composition of the ternary alloys but concurs to an appreciable reduction of the compressive stress from −5 to −4 GPa. A continuous increase and decrease in transverse sound velocity and mass density, respectively, lead to a moderate stiffening of the shear elastic constant from 130 to 144 GPa with increasing Al fraction up to x = 0.50, and a complex and nonmonotonous variation of H and EIT is observed. The maximum hardness of ∼33 GPa is found for the Mo0.81Al0.19N1.13 film, with nitrogen content close to the stoichiometric composition. The experimental findings are explained based on structural and elastic constant values computed from DFT for defect-free and metal- or nitrogen-deficient rock-salt MoAlN compounds.

The construction of structural defects in MoAlB thin films by leveraging the enhanced Kirkendall effect for improved infrared stealth performance

Synthesis, microstructure and properties of MoAlB MAB phase films

Enhancing Oxidation Resistance of MoAlB based on its Anisotropic Oxidation Mechanism: A Theoretical Calculation Guided Experimental Investigation

Development of machine learning force field for thermal conductivity analysis in MoAlB: Insights into anisotropic heat transfer mechanisms

Laser‐induced self‐propagating synthesis and electromagnetic wave absorption properties of MoAlB powders

Unexpected thermal stability of dual-phase amorphous-nanocrystalline Al0.74Mo0.26 alloy film prepared by annealing-induced crystallization

Radiation damage of MoAlB at elevated temperatures: Investigating MAB phases as potential neutron shielding materials

Microstructure, infrared optical properties and thermal stability of ZrB2 and double-layer-structure Al2O3/ZrB2 thin films by magnetron sputtering technique

Enhanced thermal stability of Mo film with low infrared emissivity by a TiN barrier layer

Preparation of fine-grained MoAlB with preferable mechanical properties and oxidation resistance

Exceptional thermal stability and mechanical properties of dual-phase amorphous-nanocrystalline Al–Mo alloy films

Structure, stress, and mechanical properties of Mo-Al-N thin films deposited by dc reactive magnetron cosputtering: Role of point defects

Microstructure evolution of thermally grown Al2O3 on NiCrAlY bonding coating for high-temperature thin-film sensors

Experimental and theoretical investigation of the damage evolution of irradiated MoAlB and WAlB MAB phases

High Thermal Stability of Nanostructured Al Mediated by Heterophase Interfaces and Nanotwinning

Microstructure evolution and oxidation behavior of bi-layer CrAl-Mo coated Zircaloy-4 in steam at 1200 o C and 1300 o C

Oxidation behavior of CrAl-Mo coated Zircaloy-4 in DB and BDB scenarios

Microstructure and mechanical properties of Mo-Ta-W refractory multi-principal element alloy thin films for hard protective coatings

Improving high-temperature wear resistance of arc-evaporated AlCrN coatings by Mo alloying

Colossal 3D Electrical Anisotropy of MoAlB Single Crystal

The Effect of MoAlB Substitutions on the Oxidation Behavior of ZrB2-SiC Composites at 1600°C