Total-energy distribution of field-emitted electrons and single-plane work functions for tungsten.

L. Swanson,L. C. Crouser

DOI: https://doi.org/10.1103/PHYSREV.163.622

1967-11-15

Abstract:Total energy distribution of field emitted electrons and single plane work functions for tungsten, discussing correspondence with Fowler-Nordheim models for field emission

Physics

What problem does this paper attempt to address?

Field-induced Hot-Electron Emission Model for Wide-Band-gap Semiconductor Nanostructures

J. Z. Zeng,S. Z. Deng,J. C. She,H. He,N. S. Xu

DOI: https://doi.org/10.1063/1.3481061

IF: 2.877

2010-01-01

Journal of Applied Physics

Abstract:For field emission from wide-band-gap semiconductor nanostructures, nonlinear plots on Fowler–Nordheim (FN) coordinates and unacceptably large field enhancement factors (βFN) are often obtained by fitting based on FN equation. In the present work, the field-induced hot-electron emission model is developed and is found to give theoretical findings consistent with the experimental observation. The hot electrons are produced by heating effect of penetration field into the emitting tip of the nanostructure. This energy is expressed by effective electron temperature Te, which is much higher than the temperature of bulk structure. By combining the effective electron temperature with thermal emission function and Murphy and Good integration function, the relation between emission current density and external field is derived and the field enhancement factor (βTe) can be calculated quantitatively. For evaluation of the theoretical model, ZnO nanostructure is selected as a concrete example. The results are found to agree with experiment findings. Extremely large field enhancement factor is not needed in our model and nonlinear property of saturation region emerges in nature in our calculation.
Monte Carlo Simulation of Secondary Electron Emission from Tungsten Surfaces with Various Work Functions As Applied to Sc/W Surfaces

T Kawano,ZJ Ding,R Shimizu

DOI: https://doi.org/10.1143/jjap.39.1877

2000-01-01

Abstract:To elucidate the secondary electron emission from tungsten surfaces of various work functions, as experimentally prepared by scandium deposition onto a W(100) surface, a Monte Carlo simulation of energy distribution of secondary electrons, N-S(E), emitted from tungsten surfaces with various work functions has been performed for comparison with the measured distribution from a Sc/W(100) surface. The Monte Carlo simulation described the shift of the onset of N-S(E) with considerable success and, furthermore, successfully predicted the appearance of a hump at around 20 eV in N-S(E), which has long been a question awaiting explaination.
Work Function of Tungsten Carbide Thin Film Calculated Using Field Emission Microscopy

孙建平,张兆祥,侯士敏,张耿民,赵兴钰,刘惟敏,薛增泉

DOI: https://doi.org/10.3321/j.issn:0372-2112.2002.05.011

2002-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:Under pressure of 1×10-6-10-5pa, a thin film of tungsten carbide is formed on the surface of tungsten tip of field emission microscopy after certain annealing treatment. Typical field emission patterns of tungsten carbide thin film is observed, and its I-V behavior and Fowler-Nordheim plot is measured. Using transmission electron microscopy, we measure the curvature radius of emission tip, and estimate the ratio factor β with an empirical formula, then calculate the work function ψ of tungsten carbide thin film to be 379eV according to Fowler-Nordheim formula.
Modified Fowler-Nordheim Field-Emission Formulae from a Nonplanar-Emitter Model

Kazuya Yuasa,Ayumi Shimoi,Ichiro Ohba,Chuhei Oshima

DOI: https://doi.org/10.48550/arXiv.cond-mat/0311573

2003-11-25

Materials Science

Abstract:Field emission formulae, current-voltage characteristics and energy distribution of emitted electrons, are derived analytically for a nonplanar (hyperboloidal) metallic emitter model. The traditional Fowler-Nordheim formulae, which are derived from a planar emitter model, are modified, and the assumption of the planar emitter in the F-N model is reconsidered. Our analytical calculation also reveals the backgrounds of the previous numerical discussion by He et al. on the effect of the geometry of emitter on field emission. The new formulae contain a parameter which characterizes the sharpness of the hyperboloidal emitter, and experimental data of field emissions from clean tungsten emitters and nanotip emitters are analyzed by making use of this feature.
Angular distribution of electron emission from ultrafast nanotip sources

Jonathan M. Geller,Michael J. Faulkner,Iona K. Binnie,Catherine Kealhofer

2024-06-12

Abstract:We investigate the angular distribution of ultrafast laser-induced electron emission from a tungsten nanotip in the multiphoton regime. A theoretical model allows precise determination of the relative contribution of different electron emission mechanisms, revealing connections between emission mechanism and the angular distribution of emitted electrons. We infer a continuous map of the work function across the surface of the tip, which in combination with the model can be used to predict values including the number of electrons per pulse and the angular divergence of the resulting beam as a function of laser power and tip voltage for (310)-oriented tungsten nanotips. The model is straightforward to implement and can be used to optimize the performance of instruments using ultrafast nanotip electron sources.

Applied Physics
Field-Emission Properties of Nanostructured Wo3 Arrays Fabricated Using Tungsten Hot-Filament Chemical Vapor Deposition

Di Lu,Akihisa Ogino,Bo Liang,Jiabin Liu,Masaaki Nagatsu

DOI: https://doi.org/10.1143/jjap.48.090206

IF: 1.5

2009-01-01

Japanese Journal of Applied Physics

Abstract:Nanostructured WO3 arrays fabricated by tungsten hot-filament chemical vapor deposition in an oxygen/argon gas mixture were studied in order to develop field-emission materials. Nanostructured WO3 arrays of different shapes were grown by controlling the substrate temperature and the distance from the hot filament. We observed that their field-emission properties strongly depended on their tip structure. Numerical calculations of field enhancement factors for different tip geometries were carried out to explain the experimental results. The numerical result reveals that the planar tip structure may help nanostructured WO3 arrays exhibit better field-emission properties.
Field Electron Emission Theory Beyond Fowler-Nordheim for Nano-Scale Emitters

Li, Zhibing,Wang, Weiliang,Qin, Xizhou,Ningsheng Xu

DOI: https://doi.org/10.1109/ivnc.2009.5271555

2009-01-01

Abstract:The standard Fowler-Nordheim theory has been widely used and achieved great success in description of field emission (FE) experiments for over 70 years. In this paper, we present the field emission models for carbon nanotubes, wide-band-gap nanowires, and metallic nanosheets, emphasizing the deviations against the Fowler-Nordheim theory and some aspects that have not been incorporated in the standard Fowler-Nordheim theory.
Electron Backscattering Coefficients of Molybdenum and Tungsten Based on the Monte Carlo Simulations

Lihao Yang,Abrar Hussain,Shifeng Mao,Bo Da,Karoly Tokesi,Z. J. Ding

DOI: https://doi.org/10.1016/j.jnucmat.2021.153042

IF: 3.555

2021-01-01

Journal of Nuclear Materials

Abstract:Monte Carlo simulation is employed for the calculation of electron backscattering coefficients of molybdenum (Mo) and tungsten (W) at normal incidence angle and at energies between 100 eV to 100 keV. For the modelling of the electron elastic scattering we have applied the partial-wave expansion method using the Mott's cross-section, where the scattering potential includes the electron electrostatic potential, exchange potential and correlation-polarization potential. A relativistic dielectric functional approach with full Penn's algorithm is adopted for the calculation of the electron inelastic cross-section. The effect of phonon excitation, the interband transition of the loosely bound valance electrons, and the inner-shells electrons excitations are considered in the energy loss functions of the materials via the optical constants. We found that our present simulated data agree well with the experimental data at energies above 20 keV for both elements while they are well above the experimental data at lower incident energies. The disagreement can be explained by the possible surface contamination of carbonaceous atomic layers exist in the measurements by additional simulation for the contaminated surfaces. Moreover, for the better and detailed understanding of the energy dependence of the backscattering coefficients, we also present the backscattered electron energy spectra, angular distributions, and depth distributions for both samples.
Improved Fowler–Nordheim equation for field emission from semiconductors

K. Jensen

DOI: https://doi.org/10.1116/1.588345

1995-03-01

Abstract:Typical qualitative experimental characterizations of current versus voltage [I(V)] for field emitters fundamentally rely on the Fowler–Nordheim (FN) equation relating the current density J to the field at the surface F. The particular form of the J(F) relationship is due to taking the zero temperature limit of a linearized Wentzel–Kramers–Brillouin (LWKB) analysis, which works well for metals, but for semiconductors it is unsatisfactory, as LWKB does not correctly calculate the energy distribution of the emitted electrons, because the electron energy is too close to an extremum of the potential barrier, especially at high fields. Consequently, estimations of the current density from semiconductors can be substantially in error. We show how to modify the WKB approach so as to minimize its deviation from the exact solution of Schrodinger’s equation, resulting in a modified WKB equation, and from it, a modified FN relation. J(F) will be compared for different semiconductors, and a comparison with metals is ...

Physics
The origin of the work function

H.C. Mastwijk,P.V. Bartels,H.L.M. Lelieveld

DOI: https://doi.org/10.48550/arXiv.0704.3797

2007-06-26

Abstract:In this paper we analyse the mechanisms responsible for the bonding of electrons to metal surfaces. We present and validate a method to measure the energy distribution of dense electron ensembles at ambient conditions. We have found sharp structures in the energy distribution of charge confined at metal surfaces. These structures correspond to the onset of space charge i.e. electron emission. The threshold energy for emission increases linear with the free electron density. We conclude that the work function is a direct measure of the Hartree-Fock exchange energy. Remarkably, the emissions that have been observed do not obey the Einstein-Millikan threshold relation for the photo electric effect. By discrimination between requirements for energy and momentum we deduce that electron emissions are trigged by photon momentum. We claim that the photo electric effect is the result of a phase transition in an electron gas that connects a surface bound, condensed state to a free continuum state. The assignment of a phase transition to the effect under consideration is justified by analyzing the behaviour of the Fermi-Dirac energy distribution upon raising the Fermi level. We predict an abrupt increment in the number of electrons in the continuum that exceeds 70 orders of magnitude. Both the observed threshold energy and the line shape of the transition are in good agreement with theoretical predictions.

Strongly Correlated Electrons
Work function and surface stability of tungsten-based thermionic electron emission cathodes

Ryan Jacobs,Dane Morgan,John Booske

DOI: https://doi.org/10.1063/1.5006029

2017-12-15

Abstract:Materials that exhibit a low work function and therefore easily emit electrons into vacuum form the basis of electronic devices used in applications ranging from satellite communications to thermionic energy conversion. W-Ba-O is the canonical materials system that functions as the thermionic electron emitter used commercially in a range of high power electron devices. However, the work functions, surface stability, and kinetic characteristics of a polycrystalline W emitter surface are still not well understood or characterized. In this study, we examined the work function and surface stability of the eight lowest index surfaces of the W-Ba-O system using Density Functional Theory methods. We found that under the typical thermionic cathode operating conditions of high temperature and low oxygen partial pressure, the most stable surface adsorbates are Ba-O species with compositions in the range of Ba0.125O to Ba0.25O per surface W atom, with O passivating all dangling W bonds and Ba creating work function-lowering surface dipoles. Wulff construction analysis reveals that the presence of O and Ba significantly alters the surface energetics and changes the proportions of surface facets present under equilibrium conditions. Analysis of previously published data on W sintering kinetics suggests that fine W particles in the size range of 100-500 nm may be at or near equilibrium during cathode synthesis, and thus may exhibit surface orientation fractions well-described by the calculated Wulff construction.

Materials Science
FIELD EMISSION MICROSCOPY STUDY OF THE WORK FUNCTION OF SINGLE-WALLED CARBON NANOTUBES

张兆祥,孙建平,侯士敏,赵兴钰,施祖进,顾镇南,刘惟敏,薛增泉

2002-01-01

Abstract:The work function of Single-Walled Carbon NanoTubes (SWCNTs) is investigated using Field Emission Microscopy (FEM). Since electron states of absorbed atoms and molecules dominate field emission from SWCNTs at room temperature, any measure prior to desorption could not obtain the work function of clean SWCNTs. So field emission patterns of clean SWCNTs are firstly achieved after SWCNTs are treated at high temperatures, then I-V behaviors of clean SWCNTs are measured. The radius of the bundle of SWCNTs is known from its image of Transmission Electron Microscopy (TEM) so that the ratio factor β could be calculated using 3 different formulas, hence the work function of clean SWCNTs is determined from the slope of Fowler-Nordheim plot.
High Accuracy Theoretical Calculation of Wavelengths and Transition Probabilities in Se- Through Ga-like Ions of Tungsten

X. L. Guo,M. C. Li,C. Y. Zhang,K. Wang,S. Li,Z. B. Chen,Y. M. Liu,H. J. Zhang,R. Hutton,C. Y. Chen

DOI: https://doi.org/10.1016/j.jqsrt.2018.02.022

2018-01-01

Abstract:The Ab initio multiconfiguration Dirac-Hartree-Fock (MCDHF) calculations of atomic parameters have been carried out with high accuracy for four highly charged tungsten ions from Se-like W40+ to Ga-like W43+. The second-order relativistic many-body perturbation theory (MBPT) was used to confirm the accuracy of the MCDHF calculations. Excitation energies, wavelengths and transition rates of El, Ml, E2, M2, E3 and lifetimes are presented. The core-valence electron correlation effects arising from deep subshells 3d and 3p, have been taken into account along with relativistic effects. The calculated wavelengths are in good agreement with available experimental results. (C) 2018 Elsevier Ltd. All rights reserved.
Surface Electronic Structures and Field Emission Currents at Sodium Overlayers on Low-Index Tungsten Surfaces

Z. A. Ibrahim,M. J. G. Lee

DOI: https://doi.org/10.1103/PhysRevB.83.165430

2010-07-13

Abstract:The total energy distributions (TEDs) of the emission currents in field emission and surface photofield emission and the overlayer-induced modifications in the surface electronic structures from the technologically important W surfaces with the commensurate W(100)/Na c(2x2), W(110)/Na (2x2) and W(111)/Na (1x1) overlayers are calculated. The TEDs obtained by our recent numerical method that extends the full-potential linear augmented plane wave method for the electronic structures to the study of field and photofield emission are used to interpret the shifts of the peaks in the experimental TEDs in field emission and photofield emission from the W(100) and W(110) surfaces at sub-monolayer and monolayer Na coverage. Hybridization of the 3s Na states with the pairs of dz2-like surface states of the strong Swanson hump in clean W(100) and surface resonances in clean W(111) below the Fermi energy shifts these W states by about -1.2 eV and -1.0 eV, thus stabilizing these states, to yield new strong peaks in the TEDs in field emission and photofield emission from W(100)/Na c(2x2) and W(111)/Na (1x1) respectively. The effect of Na intralayer interactions are discussed and are shown to shift the strong s- and p-like peaks in the surface density of states of W(110) below and above the Fermi energy respectively to lower energy with increased Na coverage, in agreement with experiments.

Mesoscale and Nanoscale Physics,Materials Science
Determination of the Energy Loss Function of Tungsten from Reflection Electron Energy Loss Spectroscopy Spectra

Z. Li,J. M. Gong,Y. Harada,B. Da,R. G. Zeng,Z. J. Ding

DOI: https://doi.org/10.1016/j.rinp.2023.107247

IF: 4.565

2024-01-01

Results in Physics

Abstract:We incorporate experimental reflection electron energy loss spectroscopy (REELS) spectrum data with theoretical analysis to precisely determine the energy loss function (ELF) of tungsten (W) in the energy loss range of 0.1–110 eV at the incident electron energies of 1 keV, 2 keV and 3 keV. Employing the reverse Monte Carlo (RMC) method, we have obtained an averaged ELF whose relative errors of the perfect-screening sum rule and oscillator-strength sum rule were ∼ 0.70 % and 0.68 %, respectively. This ELF was then used to derive the optical constants and complex dielectric function. Furthermore, we have successfully differentiated between bulk and surface contributions to the REELS spectra throughout the entire considered energy loss range.
Experimental and Theoretical Study of the Ground-Statem1 Transition in Ag-like Tungsten

Z. Fei,R. Zhao,Z. Shi,J. Xiao,M. Qiu,J. Grumer,M. Andersson,T. Brage,R. Hutton,Y. Zou

DOI: https://doi.org/10.1103/physreva.86.062501

IF: 2.971

2012-01-01

Physical Review A

Abstract:We present an experimental and theoretical study of the F-2(5/2) -> F-2(7/2) M1 transition in Ag-like W (W27+). The experiments employed the Shanghai permanent magnet electron beam ion trap, which has been developed especially for assisting spectroscopic diagnostics of edge plasmas for magnetic fusion devices. The theoretical value was obtained using the GRASP2K set of computer codes and included a comprehensive correlation study. The experimental M1 wavelength was measured as 3377.43 +/- 0.26 angstrom (3378.43 angstrom vacuum wavelength), whereas the calculated wavelength is in good agreement at 3381.80 angstrom. This good agreement shows the importance of fully understanding the electron correlation effects to predict the energy of the fine structure even in this, for tungsten, relatively simple case.
First-Principles Calculations of Field Emission from Nano-Structures

Bin Li,T. C. Leung,C. T. Chan

DOI: https://doi.org/10.1166/jctn.2006.024

2006-01-01

Journal of Computational and Theoretical Nanoscience

Abstract:A simple yet accurate self-consistent method using the density functional formalism is introduced to study the field emission properties of the nano-structures including the nanographitic armchair ribbons and the Fe bilayer on W(001) surface. The field emission currents from the armchair ribbons are dominated by the contribution from off-zone-center states because of specific wavefunction symmetries, and there exists an anomalous current density dependence on the inter-ribbons separation due to edge dipole effects. The high minority-spin-polarization of the field emission current from the Fe bilayer on W(001) surface is found, and is due to that the emission current with majority-spin is from the W substrate states but the current with minority-spin is mainly contributed by the quantum well states localized in the Fe bilayer. These rather novel properties should be ascribed to the special electronic structures of these two nano-structures.
Field Emission Properties of a Tungsten Tip after Discharge Treatment

Xiong TAO,Zhaoxiang ZHANG,Mingsheng WANG,Yue WU,Gengmin ZHANG

DOI: https://doi.org/10.3321/j.issn:0479-8023.2006.03.020

2006-01-01

Abstract:A tungsten tip received discharge treatment under a high voltage over 10 kV in a field-emission microscope (FEM). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observation showed that some nanometer-scale protrusions resulted from the discharge treatment. The post-treatment tungsten tip delivered a field emission current as high as 1.55 mA. The FEM pattern of the tip demonstrated a four-fold symmetry and thus the field emission was attributed to a single protrusion. The dependence of the field emission current on the applied voltage approximately followed the Fowler-Nordheim (F-N) theory. The value of the emission area calculated by the F-N theory is in agreement with that obtained from the TEM observation in the order of magnitude.
Determination of Charge State of Tungsten During Ultrafast Hard X-Ray Generation

Fang Shan,Vernon A Couch,Ting Guo

DOI: https://doi.org/10.1016/b978-044452821-6/50008-3

2005-01-01

The Journal of Physical Chemistry A

Abstract:High-resolution X-ray absorption measurements (with an accuracy of +/-0.3 eV) of ZnSO(4) (aq) were performed with ultrafast selected energy X-ray absorption spectroscopy (USEXAS) using a laser-driven tungsten target X-ray source. The results were used to determine the absolute spectral positions of characteristic emission lines. By comparing these positions to those predicted for the line emission from tungsten of different oxidation states using the Dirac-Fock formula, the tungsten species responsible for ultrafast hard X-ray generation were found to be tungsten atoms. This finding provides the first direct evidence to support the mechanism of X-ray generation via high-energy electrons interacting with tungsten atoms in the solid target.
Benchmarking calculations with spectroscopic accuracy of excitation energies and wavelengths in sulfur-like tungsten

Chun Yu Zhang,Kai Wang,Michel Godefroid,Per Jönsson,Ran Si,Chong Yang Chen

DOI: https://doi.org/10.1103/PhysRevA.101.032509

2020-02-26

Abstract:Atomic properties of S-like W are evaluated through a state-of-the-art method, namely, the multi-configuration Dirac-Hartree-Fock (MCDHF) method combined with the relativistic configuration interaction (RCI) approach. The level energies, wavelengths, and transition parameters involving the 88 lowest levels of W$^{+58}$ (W LIX) are calculated. We discuss in detail the relative importance of the valence- and core-valence electron correlation effects, the Breit interaction, the higher order retardation correction beyond the Breit interaction through the transverse photon interaction, and the quantum electrodynamical (QED) corrections. The present level energies are highly accurate, with uncertainties close to what can be achieved from spectroscopy. As such, they provide benchmark tests for other theoretical calculations of S-like W and should assist the spectroscopists in their assignment/identification of observed lines in complex spectra.

Atomic Physics

Total-energy distribution of field-emitted electrons and single-plane work functions for tungsten.

Field-induced Hot-Electron Emission Model for Wide-Band-gap Semiconductor Nanostructures

Monte Carlo Simulation of Secondary Electron Emission from Tungsten Surfaces with Various Work Functions As Applied to Sc/W Surfaces

Work Function of Tungsten Carbide Thin Film Calculated Using Field Emission Microscopy

Modified Fowler-Nordheim Field-Emission Formulae from a Nonplanar-Emitter Model

Angular distribution of electron emission from ultrafast nanotip sources

Field-Emission Properties of Nanostructured Wo3 Arrays Fabricated Using Tungsten Hot-Filament Chemical Vapor Deposition

Field Electron Emission Theory Beyond Fowler-Nordheim for Nano-Scale Emitters

Electron Backscattering Coefficients of Molybdenum and Tungsten Based on the Monte Carlo Simulations

Improved Fowler–Nordheim equation for field emission from semiconductors

The origin of the work function

Work function and surface stability of tungsten-based thermionic electron emission cathodes

FIELD EMISSION MICROSCOPY STUDY OF THE WORK FUNCTION OF SINGLE-WALLED CARBON NANOTUBES

High Accuracy Theoretical Calculation of Wavelengths and Transition Probabilities in Se- Through Ga-like Ions of Tungsten

Surface Electronic Structures and Field Emission Currents at Sodium Overlayers on Low-Index Tungsten Surfaces

Determination of the Energy Loss Function of Tungsten from Reflection Electron Energy Loss Spectroscopy Spectra

Experimental and Theoretical Study of the Ground-Statem1 Transition in Ag-like Tungsten

First-Principles Calculations of Field Emission from Nano-Structures

Field Emission Properties of a Tungsten Tip after Discharge Treatment

Determination of Charge State of Tungsten During Ultrafast Hard X-Ray Generation

Benchmarking calculations with spectroscopic accuracy of excitation energies and wavelengths in sulfur-like tungsten