Abstract:The interface morphology of the bonding layer has a considerable effect on the damage and failure of sandwich-structured thermal barrier coatings. This work investigated the comprehensive effects of a grooved texture produced using laser ablation on the local surface strain, interfacial stress and strain, and crack behavior of the bonding layer in a thermal barrier coating system. The distribution and evolution of the local surface strain was obtained using the digital image correlation method. The interfacial stress, and the strain between the ceramic and bonding layers, were determined through a simulation of the plane-strain model, and the morphology and propagation of cracks were observed in thermal barrier coatings under an external tensile load. The results indicated that the local surface strain of the thermal barrier coating increased with the texturization of the bonding layer, whereas the fluctuation decreased. There were two inflection points in the local surface strain–time curves, corresponding to the initiation of surface cracks and that of interfacial transverse cracks. The surface cracks were initiated earlier than those without the texturization of the bonding layer. However, the behavior of the interfacial cracks was more complicated. If the roughness of the texture, defined as Rc, was small, the surface cracks propagated vertically to the interface between the ceramic and bonding layers, and turned into transverse cracks, leading to a separation of the ceramic layer. If Rc was greater than 22 μm, the surface cracks went further down to the interface between the bonding layer and substrate, and propagated horizontally, resulting in the separation of both the ceramic and bonding layers. Meanwhile, interfacial cracking and separation were deferred. A large roughness resulted in good cohesion between the ceramic and bonding layers, and a high stiffness for the coating, which improved the damage resistance and extended the life of the coating.

Effect of the interface morphology and initial nanocrack on the fracture property of a ceramic reinforced plasma-sprayed coating

Activating Continuous Dislocation Pinning Enhanced Toughness of Nanocomposite Coating Through Specially Oriented Semicoherent Heterointerface Lattice Distortion

The Effect of Annealing on Microstructure and High Temperature Erosion Property of Arc-Spraying Coatings Containing Nanosized Ceramic Powders

Edge Effect on Crack Patterns in Thermally Sprayed Ceramic Splats

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Particle Impact Damage and Point Load-Induced Fracture Behavior in Zirconia Plasma Spray Coating Film

On crack evolution with texturization of bonding layer in thermal barrier coating

Characterization of the Interfacial Structure and Fracture Behavior of in Situ Synthesized Ceramics to Reinforce Ni-based Composite Coatings

Understanding the relationship between microstructure and mechanical behavior of plasma-sprayed amorphous Al2O3–YAG ceramic coating based on depth-sensing indentation measurements

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Discrete element modeling of effect of interfacial roughness and pre-crack on crack propagation in thermal barrier coatings

Influences of Interface Properties and Coating Thickness on Fracture Behaviors of Coating/substrate Systems

The role of ceramic particles on the crack inhibition and mechanical properties improvement of Haynes 230 alloy fabricated by laser powder bed fusion

Interfacial metal/ceramic bonding mechanism for metallization of ceramics via cold spraying

Indentation deformation and microcracking in β-Si 3N 4-based nanoceramic

Microstructure effects on fracture failure mechanism of CrAl/CrAlN coating

Friction and wear characteristics of in-situ Cr+(Cr,Al)2O3 composite coating fabricated by plasma spraying

Morphology and formation mechanism of cracks in Al2O3–ZrO2 eutectic ceramics fabricated via laser powder bed fusion

Effect of Interfacial Structure on Microstructure and Properties of Cold-Sprayed Cu-Al2O3 Composite Coating

Relationship between particle interface structure and performance of cold sprayed CuCrZr deposit

Microstructure, cracking susceptibility and abrasive wear resistance of core-shell ceramic particles reinforced laser cladding coatings