Abstract:A novel one-step liquid plasma-assisted particle deposition and sintering (LPDS) method is used to prepare a ZrC–ZrO2 nanocomposite ceramic coating on a TiAlNb medium-entropy alloy to enhance its ablation resistance. For comparison, a conventional plasma electrolytic oxidation (PEO) ceramic coating is fabricated on a substrate without ZrC particles. Results show that numerous ZrC particles are introduced into the coating, accompanied by partial oxidation to ZrO2 during the LPDS. The thickness of the nanocomposite coating increases significantly by approximately 11.4 times compared with that of the PEO coating. At 1000 °C, the ablation thickening of the ZrC–ZrO2 nanocomposite coating is approximately 1/4 of that of the substrate after ablation in air. Moreover, 17.88% and 2.83% of the substrate surface and PEO coating are peeled, respectively, whereas no peeling occurred in the ZrC–ZrO2 nanocomposite coating. This can be attributed to the high melting point and exceptional toughness of ZrO2, which allow it to absorb the stress caused by thermal shocks and inhibit crack formation. A thick nanocomposite coating is crucial for protecting the substrate by preventing oxygen from permeating the coating and oxidizing the substrate. Additionally, the glass phase of SiO2 densifies the pores and cracks in the coating, thereby significantly inhibiting the inward diffusion of oxygen and preventing ablation. Therefore, LPDS is a novel strategy for designing and fabricating multifunctional coatings to enhance the thermal protection of alloy substrates via the incorporation of various functional particles.

Ablation behavior of sharp leading edge parts made of rare earth La-compound modified ZrB2 coated C/C composites

Preparation and ablation resistance of ZrC nanowires-reinforced CVD-ZrC coating on sharp leading edge C/C composites

Ablation behavior of high-entropy boride (Hf-Zr-Ta-Ti)B 2 coating fabricated via supersonic atmospheric plasma spraying for carbon/carbon composites

Ablation behavior of La 2 O 3 modified C/C–ZrC composites fabricated by precursor infiltration and pyrolysis

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Long-term and cyclic ablation behavior of La2O3 modified Cf/ZrB2-SiC composites at 2500 °C

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation

Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

Anti-ablation Performance of Plasma Sprayed ZrB2/SiC Coatings on C/C Substrates and the Influence of a Chemical Vapor Deposited SiC Interlayer

Enhanced ablation resistance of ZrC–ZrO2 nanocomposite ceramic coating on TiAlNb medium-entropy alloy prepared by a novel strategy

Anti-ablation performance of plasma sprayed ZrB 2 /SiC coatings on C/C substrates and the influence of a chemical vapor deposited SiC interlayer

Ablation Behaviour of C/C–ZrC Composites in a Solid Rocket Motor Environment

Ablation behaviour of the CVD-(ZrC/SiC)3 alternate coating on C/C composites under oxyacetylene torch with different heat fluxes

Ablation of advanced C/C-ZrC-SiC leading edge composites

Multi-cycle and long-term ablation behavior of Cf/ZrB2-SiC composites at 2500 °C

Ablation behavior of C f /ZrC–SiC ultra–high temperature ceramic composites in oxyacetylene torch and plasma wind tunnel

Influences of deposition temperature, gas flow rate and ZrC content on the microstructure and anti-ablation performance of CVD-HfC-ZrC coating

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Study on the mechanism of ultra-high temperature ablation of ZrB2–SiC–TaSi2 coatings by low-pressure plasma spraying on the C/C composites

Phase transitions and microstructure evolutions of in-situ YSZ-ZrC composite coating under long-time plasma torch ablation