Abstract:Based on the inherent ablation issues under the hostile thermochemical environment in solid rocket motors (SRM), a dual-scale ablation model of C/C composite nozzle is established. It investigates the ablation rate from both macroscopic and microscopic perspectives. The mechanical erosion of particles and the chemical reaction of gas are comprehensively considered. At macroscale, the turbulence model is proposed to obtain the temperature distribution and the flow field of the nozzle; the particle tracking model is applied to analyze the degree of mechanical erosion and it demonstrates 0.94% ~ 1.88% of the particles will eventually be deposited on the wall. At microscale, the regression and morphology of the surface of C/C composites are simulated by level set method, and the thermochemical ablation law of fibers and matrix is revealed. In addition, the influence of changes in microscopic morphology on surface reaction is input to the macroscale model, and a more convincing chemical ablation rate is evaluated. In the typical ablation conditions, the chemical ablation rate and mechanical erosion rate of the nozzle are respectively estimated as 0.03 mm/s and 0.0063 mm/s, which accords well with the reported data. Thus, our model identifies two extreme situations, i.e., when there are lots of Al2O3 particles, nozzle erosion is dominated by mechanical erosion, but when Al2O3 particles are very few, chemical ablation plays a major role. The limit ratio of mechanical erosion and chemical ablation are calculated. The results of the present study provide a deeper understanding of the ablation mechanism of C/C composite nozzle, which is useful for the thermal performance research and design of C/C nozzle.

Ablation Behaviour of C/C–ZrC Composites in a Solid Rocket Motor Environment

Microstructure and ablation behaviour of C/C-SiC-ZrC-Cu composites prepared by reactive melt infiltration

Ablation mechanism of C/C–SiC and C/C–SiC–ZrC composites in hypersonic oxygen-enriched environment

Ablation behavior of C/C–Zr1-xHfxC-SiC composites under an oxyacetylene flame at above 2500 °C

Mechanical and Ablation Properties of Three-Dimensional ZrC Skeleton Reinforced Graphite-Based Composites

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Microstructure and Ablation Behavior of C/C-SiC-(ZrxHf1−x)C Composites Prepared by Reactive Melt Infiltration Method

Ablation and mechanical behaviour of C/C composites under an oxyacetylene flame and tensile loading environment

Microstructure and Ablation Performance of SiC–ZrC Coated C/C Composites Prepared by Reactive Melt Infiltration

Ablation behaviors of ultra-high temperature ceramic composites

Ablation-resistance of ZrB2-SiC Coating under Oxygen-propane Torch Flame Prepared by Atmospheric Plasma Spraying

Ablation behavior of C f /ZrC–SiC ultra–high temperature ceramic composites in oxyacetylene torch and plasma wind tunnel

The mechanical properties of C/C-ZrC-SiC composites after laser ablation

Ablation performance of C/C-ZrC-SiC composites with in-situ YSi 2 -doped ZrC-SiC-ZrSi 2 coating under oxyacetylene torch

Cyclic Ablation Behaviors of ZrB2–SiC Composites Sintered with Nano‐Sized Particles

Numerical analyses of ablative behavior of C/C composite materials

A Dual-scale Model for Estimating the Ablation Rate of C/C Composite Nozzle

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Effect of Carbide Particles on the Ablation Properties of Tungsten Composites

Enhanced ablative resistance of C/C composites with densified ZrB 2 -based ceramics by incorporation of Mo as interface layer

Ablation behavior of three-dimensional C f /SiC-ZrC-ZrB 2 composites prepared by a joint process of sol-gel and reactive melt infiltration