Abstract:Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) was developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) were comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibited a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at −20 °C. In contrast, the HR-QT steel exhibited tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consisted of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reached 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared with the HR-QT process, the TMCP-DQP process resulted in a finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieved the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilized the RA through carbon enrichment, while the relaxation stage reduced a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminated internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Pre-quenching induced lath structures and enhanced TRIP effect to optimize the strength-ductility of ultrahigh-strength hot-galvanized steel

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Overcoming the Trade-off Between Strength and Ductility in Austenitic Stainless Steel Using a High-Density Pulsed Electric Current

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

The Fabrication of Ultrahigh-Strength Steel with a Nanolath Structure via Quenching-Partitioning-Tempering

Transformation-Induced Ductility of Reverse Austenite Evolved by Low-Temperature Tempering of Martensite

Effects of quenching temperature on bainite transformation, retained austenite and mechanical properties of hot-galvanized Q&P steel

Improvement of Strength-Toughness-Hardness Balance in Large Cross-Section 718H Pre-Hardened Mold Steel

Enhanced Yield Strength and Total Elongation of an Ultrahigh Strength Hot‐Stamped Steel via Tempering Treatment

Improving the ultimate tensile strength without loss of plasticity of quenching-partitioning steel by introducing hot deformation

Ultrahigh strength-ductile medium-Mn steel auto-parts combining warm stamping and quenching & partitioning

Through a Controlled Quenching to Achieve a Good Combination of Mechanical Properties in Low‐Yield Ratio 900 MPa High‐Strength Low‐Alloy Steels

Effect of hot stamping and quenching & partitioning process on microstructure and mechanical properties of ultra-high strength steel

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Enhanced strength-ductility synergy in a new 2.2 GPa grade ultra-high strength stainless steel with balanced fracture toughness: Elucidating the role of duplex aging treatment

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

Batch annealing enhances the yield strength of a high quenching temperature Q&P steel through accelerated bainitic transformation

Effect of Intercritical Annealing Parameters and Starting Microstructure on the Microstructural Evolution and Mechanical Properties of a Medium-Mn Third Generation Advanced High Strength Steel

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes

Achieving 2.2 GPa Ultra-High Strength in Low-Alloy Steel Using a Direct Quenching and Partitioning Process