Abstract:Highlights • The TaCl 5 doped SnSe 0.95 samples were synthesized by melting and SPS technology. • The increased carrier concentration promoted the increased power factor. • The extra Sn was stabilized by Ta. • A lowest κ l (0.24 W·m –1 ·K –1 at 773 K) was obtained in n-type polycrystalline SnSe 0.95 system. • A record zT ave (0.62 from 323–773 K) was obtained in n-type polycrystalline SnSe 0.95 system. The average zT determines the conversion efficiency, and the power factor plays an important role in average zT value. However, the inadequate electrical conductivity of SnSe materials seriously limits its application. Herein, the TaCl 5 -doped in polycrystalline SnSe 0.95 materials synthesized using the melting method and combined with spark plasma sintering technology achieves a zT value of 1.64 at 773 K and a record zT ave of 0.62 from 323 K to 773 K. The electrical conductivity increases due to the released electron carrier induced by effective TaCl 5 doping. According to the DFT calculation, the energy band of TaCl 5 -doped samples is narrowed, which can enhance the electron transport. Besides, the Seebeck coefficient is maintained at an elevated level as a result of the incorporation of the heavy element Ta. Due to the significantly enhanced electrical conductivity and maintained high Seebeck coefficient, the power factor reaches to 622 μW·m –1 ·K –2 at 773 K for the SnSe 0.95 + 1.75% (in mass) TaCl 5 sample, which is almost 21 times higher than that of the pristine sample. Simultaneously, a high average power factor value of 334 μW·m –1 ·K –2 for the SnSe 0.95 + 1.75% (in mass) TaCl 5 sample from 323 to 773 K was obtained. It is surprisingly found that the Ta element plays another important role to improve the stability of SnSe 0.95 by forming Ta 2 Sn 3 and removing the low melting point Sn, which usually existed in n-type SnSe samples, resulting in the decreased lattice thermal conductivity. A low lattice thermal conductivity value of 0.24 W·m –1 ·K –1 was also obtained for the SnSe 0.95 + 2.0% (in mass) TaCl 5 sample at 773 K due to the multiscale defects. Consequently, the SnSe 0.95 + 2.0% (in mass) TaCl 5 sample obtains a peak zT value of 1.64 at 773 K and a record zT ave of 0.62 from 323 to 773 K, and the theoretically calculated conversion efficiency reaches 11.2%, it can be utilized for power generation and/or cooling at a broad temperature range. This strategy of introducing high-valence halides with heavy element can optimize the thermoelectric performance for other material systems. Graphical abstract Download : Download high-res image (307KB) Download : Download full-size image

Ultrahigh average zT realized in polycrystalline SnSe 0.95 materials through Sn stabilizing and carrier modulation

High thermoelectric properties in polycrystalline SnSe materials realized by rare earth halide Co-doping

Enhancement of Thermoelectric Performance of Layered SnSe2 by Synergistic Modulation of Carrier Concentration and Suppression of Lattice Thermal Conductivity

Realizing high thermoelectric properties in p-type polycrystalline SnSe by inducing DOS distortion

Improved thermoelectric properties of n-type polycrystalline SnSe via carrier concentration optimization

Realizing High Thermoelectric Performance in P-Type SnSe Through Crystal Structure Modification

Studies on thermoelectric figure of merit of Na-doped p-type polycrystalline SnSe

Ultrahigh Average ZT Realized in P-Type SnSe Crystalline Thermoelectrics Through Producing Extrinsic Vacancies.

Enhanced thermoelectric performance of highly oriented polycrystalline SnSe based composites incorporated with SnTe nanoinclusions

Enhanced Thermoelectric Properties of Polycrystalline SnSe via LaCl3 Doping

Enhanced thermoelectric performance of n-type polycrystalline SnSe via NdCl3 doping

Realizing High Thermoelectric Performance in Slightly Na-doped SnSe Polycrystals

Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal

Realizing high doping efficiency and thermoelectric performance in n-type SnSe polycrystals via bandgap engineering and vacancy compensation

Lattice Strain Leads to High Thermoelectric Performance in Polycrystalline SnSe

Re‐Doped p‐Type Thermoelectric SnSe Polycrystals with Enhanced Power Factor and High ZT > 2

Enhanced thermoelectric performance of AgCuTe-doped polycrystalline SnSe by lattice plainification

Realizing High Thermoelectric Performance of Ag/Al Co‐Doped Polycrystalline SnSe through Band Structure Modification and Hydrogen Reduction

Enhancing Thermoelectric Performance of K-doped Polycrystalline SnSe Through Band Engineering Tuning and Hydrogen Reduction

Enhanced Thermoelectric Performance of P-Type SnSe Doped with Zn

Achieving high thermoelectric performance with Pb and Zn codoped polycrystalline SnSe via phase separation and nanostructuring strategies