Abstract:Purpose Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens. Design/methodology/approach This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature. Findings It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process. Originality/value 316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

Mesostructured emerging 316L-17-4PH composite steel parts by material extrusion for the property maximization through an efficient microstructural design

Microstructural Control of a Multi‐Phase PH Steel Printed with Laser Powder Bed Fusion

Optimization of the extrusion rate for different layer thicknesses to achieve controlled mechanical properties in MEX 3D printing of low-alloy steel

A Facile and Sustainable Integrated Fabrication Strategy for Multi-Performance 316l Stainless Steel

An ultra-high strength martensitic steel fabricated using selective laser melting additive manufacturing: Densification, microstructure, and mechanical properties

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

Evaluation of material extrusion and laser-assisted in situ consolidation integrated additive manufacturing for multi-material components

17-4 PH Steel Parts Obtained through MEX and PBF-LB/M Technologies: Comparison of the Structural Properties

Mesostructure engineering in additive manufacturing of alloys

Material extrusion-based fabrication of 316L stainless steel: analysis of debinding and sintering, mechanical properties, and corrosion resistance

Microstructure evolution, phase formation, corrosion, and mechanical properties of stainless steel fabricated by extrusion-based sintering-assisted additive manufacturing

Optimization of metallic powder filaments for additive manufacturing extrusion (MEX)

Systematic Evaluation of Adhesion and Fracture Toughness in Multi-Material Fused Deposition Material Extrusion

The impact of interfacial characteristics on the interfacial properties of 316 L/CuSn10 multi-material manufactured by laser powder bed fusion

Additive manufacturing of 316L stainless-steel structures using fused filament fabrication technology: mechanical and geometric properties

Material Extrusion to Manufacture Carbide-Based Advanced Cutting Tools

The enhancement of mechanical properties via post-heat treatments of AISI 630 parts printed with material extrusion

Advancements in Metal Additive Manufacturing: A Comprehensive Review of Material Extrusion with Highly Filled Polymers

Steel Chips as a Raw Material for MEX

Prototyping and characterisation of 316L stainless steel parts and lattice structures printed via metal fused filament fabrication

Influence of Binder Composition and Material Extrusion (MEX) Parameters on the 3D Printing of Highly Filled Copper Feedstocks