Abstract:Nanofibers exist ubiquitously in natural extracellular matrix (ECM) of all kinds of human tissues forming hydrated interwoven network. Electrospinning nanotechnology has been proven to be a powerful technique to fabricate controllable nanofibers mimicking the natural ECM structures. Hyaluronic acid (HA), as a critical component of natural ECM, has been widely used in tissue engineering and regenerative medicine. In this study, pure HA nanofibers with average diameter of 33 +/- 5 nm, 59 +/- 12 nm, 79 +/- 12 nm and 113 +/- 19 nm were successfully prepared using different electrospinning parameters. The effect of the ambient relative humidity on HA electrospinnability was investigated for the first time in detail, which was proven to be one of the most important factors to control the morphology of HA nanofibers beside the solution properties. A critical value of humidity for a defined HA solution was observed, only below which HA nanofibers with similar diameters and morphologies could be successfully obtained. When the ambient relative humidity was higher than the critical value, the HA nanofibers started dissolving at the cross points and even fused together forming a spreading layer. Moreover, only a small amount of N, N-Dinnethylformamide (DMF) was found to be required to promote the electrospinnability of HA solution by mixing with water as solvents. With the increase in the DMF content, the surface tension of the solution decreased significantly, which was thought to be benefit for the stable Taylor cone and fluid jet formation in electrospinning. At the same time, it should be noted that the conductivity of the solution also decreased with the increase of DMF content in the solution, which was believed to be responsible for the increasing diameters of HA nanofibers corresponding to higher DMF content. Controllable HA nanofibers with diameter below 100 nm have great promising for developing novel nanobiomaterials applied in tissue engineering and regenerative medicine.

Molecular Interaction, Chain Conformation, and Rheological Modification during Electrospinning of Hyaluronic Acid Aqueous Solution

Effects of ambient relative humidity and solvent properties on the electrospinning of pure hyaluronic acid nanofibers.

Effect of hyperbranched poly(ester amine) additive on electrospinning of low concentration poly(methyl methacrylate) solutions

IMPROVEMENT OF POLY(METHYL METHACRYLATE) ELECTROSPUN FIBER UNIFORMITY BY ADDITION OF POLY(ESTER AMINE)

Experimental Investigation of the Effect of Processing Parameters on the Formation of Electrospun Polyethylene Oxide Nanofibers

Optimized Electrospinnability and Chemical Crosslinking of Nanofiber Membranes with High-content Hyaluronic Acid for Anti-coagulant Application

Nanofibrous Mats of Rigid Polysaccharides Prepared by Coaxial Electrospinning

Electrospinning of sodium alginate with poly(ethylene oxide)

Effects of Solvent on Structures and Properties of Electrospun Poly(ethylene Oxide) Nanofibers

High-Elongation Fiber Mats by Electrospinning of Polyoxymethylene

Biocompatible Native Hyaluronan Nanofibers Fabricated via Aqueous PEO-Assisted Electrospinning and Heat-Quench Process

Effect of Solution Composition Variables on Electrospun Alginate Nanofibers: Response Surface Analysis

Interaction Between Poly(vinyl Alcohol) and Layered Double Hydroxide (LDH) Particles with Different Topological Shape and Their Application in Electrospinning

Influence of interfacial compatibility on the crystallization behavior of electrospun core–sheath fibers

Experimental Investigation of the Governing Parameters in the Electrospinning of Polyethylene Oxide Solution

Study on electrospinnability of PVP/PEO composite micro-nano fibers

Effects of Poly(3-hexylthiophene) Molecular Weight and the Aging of Spinning Solution on the Electrospun Fiber Properties

Synergistic effect of electric field and polymer structures acting on fabricating beads-free robust superhydrophobic electrospun fibers

Electrospun Alginate Fibers: Mixing of Two Different Poly(ethylene oxide) Grades to Improve Fiber Functional Properties

A General Strategy to Electrospin Nanofibers with Ultrahigh Molecular Chain Orientation

Effect of Experimental Parameters on Morphological, Mechanical and Hydrophobic Properties of Electrospun Polystyrene Fibers