Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Effects of C/Si ratios on structures and behaviors of NbSiCN nanocomposite films synthesized by reactive magnetron sputtering

Microstructure and Mechanical Properties of SiCN Hard Films Deposited by an Arc Enhanced Magnetic Sputtering Hybrid System

The Structure, Surface Topography and Mechanical Properties of Si–C–N Films Fabricated by RF and DC Magnetron Sputtering

Surface Roughness, Mechanical Properties and Bonding Structure of Silicon Carbon Nitride Films Grown by Dual Ion Beam Sputtering

Effects of silicon content on the structure and mechanical properties of (AlCrTaTiZr)–Si<sub><i>x</i></sub>–N coatings by reactive RF magnetron sputtering

Microstructures and mechanical properties of Zr-Si-N films prepared by reactive sputtering

Tribological Properties of CrSiN Nanocomposite Films

Effect of the deposition conditions on the morphology and bonding structure of SiCN films

Microstructure and Mechanical Properties of Carbon Nitride Multilayer Films Deposited by DC Magnetron Sputtering

Effects of silicon content on the structure and mechanical properties of (AlCrTaTiZr)–Six–N coatings by reactive RF magnetron sputtering

Effect of Electron Beam Irradiation on Structure and Properties of SiCN Thin Films Prepared by Plasma Assisted Radio Frequency Magnetron Sputtering

Silicon-content-dependent microstructures and mechanical behavior of (AlCrTiZrMo)-Six-N high-entropy alloy nitride films

STRUCTURAL ANALYSIS OF SiCN FILM PREPARED BY REACTIVE SPUTTERING

Structure and Lubricated Tribological Behavior of Silicon Incorporated Carbon Nitride Composite Films Deposited by Magnetron Sputtering

Mechanical Properties of Silicon Carbonitride Thin Films

Effect of Si on the Mechanical and Tribological Properties of FeCoNiBSiNb Amorphous Alloy Composites Prepared by Laser Melting

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Effects of Silicon Content on the Microstructures and Mechanical Properties of (AlCrTiZrV)-Six-N High-Entropy Alloy Films

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Microstructure, Mechanical Properties and Wetting Behavior of F: Si–C–N Films As Bio-Mechanical Coating Grown by DC Unbalanced Magnetron Sputtering

Effects of Atomic Ratio on the Mechanical Properties of Amorphous Silicon Carbon Nitride